Agilent Technologies 53230A Spezifikationen Seite 138
- Seite / 260
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 2 Service
The Agilent 53210A/53220A/53230A Calibration Procedures
138 Assembly-Level Service Guide
2Press Auto Cal.
• Display stops updating until auto-calibration is completed (several
seconds).
• If the calibration is successful, the screen displays “Auto Calibration
succeeded”.
– Cal Count is not updated, but the calibration constants ARE
updated.
• If any one of the calibration routines fails, the screen displays “Auto
Calibration failed”.
NOTE When the auto-calibration completes, a pass/fail message will be
displayed. If the calibration failed, then the current calibration
constants remain unchanged.
3 If the auto-calibration fails (“Auto-calibration failed”), first verify
any inputs connected to the counter are turned OFF. Then, refer
to the troubleshooting procedures starting on page 150 .
4 To check for error messages, refer to the “
Summary of Remote
Auto-Calibration
” below for information on how to read the
error message(s) from a remote computer.
NOTE If you do not have a remote computer available (requires a LAN,
USB or GPIB interface) or are not proficient at programming,
contact the nearest Agilent Service Center for information and
help on sending the counter to Agilent for repair and/or
calibration.
5 If you are able to read the error message(s), consult “Error
Messages” starting on page 163 for what to do after receiving a
specific calibration error message.
- Agilent 53200 Series 1
- 350 MHz Universal 1
- Frequency Counters/ 1
- Safety Information 3
- 1 Watt Max into 50W 4
- Channel / Setup 4
- Contents 10
- Performance Tests 11
- Introduction 12
- Chapter Overview 13
- Remote testing of the Counter 14
- Performance Test Record 14
- Test Considerations 14
- Recommended Calibration Cycle 15
- Equipment Required 16
- Power-On Test 17
- Self-Test (Q) 19
- Verification 21
- Termination Checks (Optional) 23
- Equipment 26
- CG635 Signal Generator Setup 26
- Counter Setup 26
- *Opt 150 28
- Test 3: Single Period 37
- Single Period Test Procedure 41
- Test 4: (Q) Pulse Width 43
- Pulse Width Test Procedure 47
- Test 5: (Q) Time Interval 48
- 81134A Setup 49
- 106 (6 GHz Microwave Channel) 53
- E8257D-520 Setup 54
- U S B L AN 60
- Option 150 With Option 106 65
- Option 150 With Option 115 71
- Test Record (Tests 1 to 7) 78
- Technologies for Service 92
- To Provide Repair Information 93
- Warranty 95
- Calibration Menu 96
- From the Counter Front Panel 100
- To Lock the Counter: 102
- Unlock For Calibration: 103
- Calibration Procedures 105
- MY50000125 107
- Calibration Cycle 108
- Calibration String: 108
- RF Signal 109
- Generator 109
- Chapter 2 Service 114
- Summary of Internal 119
- DAC Remote Calibration 119
- 0 means OFF or unlocked 120
- Microwave 122
- “Calibration step succeeded.” 125
- Summary of Option 127
- for 53220A/53230A 128
- for 53210A 128
- Internal Auto-Calibration 136
- To Run AutoCalibration: 137
- Summary of Remote 138
- Auto-Calibration 138
- To View the Calibration Count 139
- Safety Considerations 142
- Recommended Test Equipment 143
- Repair Considerations 144
- After Service Considerations 145
- Troubleshooting the Counter 150
- Battery Operation 154
- Preliminary Steps 154
- Testing the battery 156
- Normal Battery Operation 157
- Remote Battery Commands 158
- Reseat the Boards 162
- Re-Run the Counter Self Test 162
- Error Messages 163
- P0500-63001 processor board 164
- P0500-63001 processor 164
- Query Errors (-400...) 166
- Calibration Errors (700...) 166
- Self-Test Errors (901...) 167
- Replacing Assemblies 169
- Tools Required 171
- Electrostatic Discharge 172
- Assembly (Option 300) 175
- To Remove the GPIB Assembly 177
- To Remove the Processor Board 181
- Motherboard 183
- To Remove the Motherboard 186
- Retrofitting Options 189
- Do This First 191
- Timebase (Option 010) 193
- Power (Option 300) 196
- Y-CableDigital Cable 199
- Inputs (Option 201) 202
- Semi-Rigid 212
- Position 212
- Front Flange 212
- Option 106 214
- T20 TORX Screw 225
- Measurements) for the 53230A 236
- Replaceable Parts 237
- How To Order A Part 240
- Customer Order 243
- MOTHERBOARD 244
- Chapter 5 Replaceable Parts 246
- Backdating 247
- Backdating Firmware 250
- Procedure Changes 252
- Freq) <frequency> 257
- Backdating Hardware 259
- Backdating Specifications 260
Verwandte Produkte und Handbücher für Multimeter Agilent Technologies 53230A
(85 Seiten)
(22 Seiten)
(133 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern