Agilent Technologies 8000 Series Spezifikationen Seite 64
- Seite / 162
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 3: Testing Performance
Performance Test Record
64
Performance Test Record
Agilent Technologies
Agilent 8000 Series Oscilloscopes
Model Number _____________________ Tested by___________________
Serial Number ___________________________ Work Order No.___________________
Recommended Test Interval - 1 Year/2000 hours Date___________________
Recommended next test date ___________________ Ambient temperature ___________________
Test Limits Results
(Vmax - Vmin)/4.8 =Limits
DC Calibrator
Amplitude
1.000 0.998 to 1.002 ___________________
Channel 1 Channel 2 Channel 3 Chan 4/Ext
Input
Resistance
50
Ω 49.25 Ω to 50.75 Ω ___________ ___________ ___________ ______/_____
1 M
Ω 990 kΩ to 1.010 MΩ ___________ ___________ ___________ ______/_____
Time Scale
Accuracy
Limit
Limit is based on oscilloscope’s age
Calculated
TSA Spec
Measured time
scale error
Pass/Fail
TSA ≤ ± (15 + 2 * YrsSinceMfr) ppm ___________ ___________ ___________
MSO8064A,
DSO8064A
Delta Time
Measurement
Accuracy
Limits Results
Averaged Mode DTMA Channel 1 Channel 2 Channel 3 Channel 4
Maximum (ps) 3326.2 ___________ ___________ ___________ ___________
Minimum (ps) 3318.3 ___________ ___________ ___________ ___________
Std. Deviation (ps rms) 1.2 ___________ ___________ ___________ ___________
Non-Averaged Mode DTMA Channel 1 Channel 2 Channel 3 Channel 4
Maximum (ps) 3352.2 ___________ ___________ ___________ ___________
Minimum (ps) 3292.3 ___________ ___________ ___________ ___________
Std. Deviation 6.8 ___________ ___________ ___________ ___________
MSO8104A,
DSO8104A
Delta Time
Measurement
Accuracy
Limits Results
Averaged Mode DTMA Channel 1 Channel 2 Channel 3 Channel 4
Maximum (ps) 1998.0 ___________ ___________ ___________ ___________
Minimum (ps) 1994.0 ___________ ___________ ___________ ___________
Std. Deviation 0.38 ___________ ___________ ___________ ___________
Non-Averaged Mode DTMA Channel 1 Channel 2 Channel 3 Channel 4
Maximum (ps) 2023.0 ___________ ___________ ___________ ___________
Minimum (ps) 1969.0 ___________ ___________ ___________ ___________
Std. Deviation (ps rms) 5.7 ___________ ___________ ___________ ___________
- Service Guide 1
- In This Book 5
- Contents 7
- 6 Replacing Assemblies 8
- 7 Replaceable Parts 8
- 8 Theory of Operation 8
- General Information 10
- Accessories supplied 13
- Accessories available 14
- Options available 15
- ± 5°C from the temperature 16
- Environmental Conditions 17
- Measurement Category 17
- Oscilloscope Dimensions 18
- Preparing for Use 19
- Setting Up the Oscilloscope 20
- To inspect package contents 21
- Figure 2-1 21
- To connect power 22
- Attaching the Probe Connector 25
- Probing the Circuit 26
- To connect the digital probe 28
- Digital probe lead set 29
- 40-pin Connector Pinout 30
- Figure 2-14 31
- To turn on the oscilloscope 32
- To turn off the oscilloscope 32
- Probe Compensation 33
- To clean the oscilloscope 35
- Testing Performance 37
- Clear Display 39
- Averaging 39
- Specifications 39
- Performance Test Procedures 39
- Fluke MET/CAL Procedures 39
- To test the DC calibrator 40
- To test input resistance 42
- Connect the equipment 43
- Select Close 45
- (Supply) Minimum Maximum 45
- Set the scale from the 46
- Set the offset from the 46
- To test bandwidth 47
- To verify threshold accuracy 49
- Connections 50
- High-to-Low Transitions 55
- Threshold Voltage Setting V2 56
- Low-to-High Transitions 57
- To test time scale accuracy 59
- Oscilloscope 60
- Sine Wave Source 60
- Frequency Reference 60
- Agilent Technologies 64
- Range Supply Limits 65
- Performance Test Record 66
- Calibrating and Adjusting 67
- To run the self calibration 69
- Troubleshooting 71
- Default Setup 73
- 54830F01a 75
- Primary Trouble Isolation 76
- Run oscilloscope self-tests 77
- Self Calibration 78
- Performance” on page 37 78
- No Display Trouble Isolation 79
- Input Pin # 7 65432 1 81
- Replace any shorted assembly 84
- Replace the power supply 84
- To check probe power outputs 85
- To Check the keyboard 86
- To check the LEDs 87
- Intel D915GUX Motherboard 88
- To Reset 89
- 5 and 7 89
- To setup the BIOS 91
- Figure 5-12 93
- Software Revisions 94
- Replacing Assemblies 95
- Bottom sleeve fasteners 99
- Removing bottom sleeve 100
- Connecting Mylar flex sables 101
- Disconnecting W8 104
- Access Hole 105
- Removing the BNC nuts 108
- Figure 6-17 112
- Opening in side of 131
- Fan control board cables 131
- Acquisition board cables 131
- Figure 6-32 132
- Lift board out of chassis 134
- To remove and replace a fan 135
- Mylar flex cables 136
- T10 Torx Screws 136
- Replaceable Parts 137
- Power Cords 139
- Exploded Views 140
- Replaceable Parts List 145
- Theory of Operation 149
- Figure 8-1 150
- Logic Trigger 154
- Attenuator Theory 155
- Acquisition Theory 155
- • Trigger levels 156
Verwandte Produkte und Handbücher für Messen, Testen & Steuern Agilent Technologies 8000 Series
(92 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern