Agilent Technologies 8000 Series Spezifikationen Seite 15
- Seite / 162
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 1: General Information
Options available
15
Options available
The following options are available for the Infiniium oscilloscope. Other options may be available.
See your Agilent Technologies Sales Representative or visit www.agilent.com and perform a
search for your oscilloscope’s model number.
Table 1-2
8000 Series Oscilloscope Options
Calibration Option
A6J ANSI Z540-Compliant Calibration
Factory-Installed
Instrument Options
040 Increase acquisition memory to 8 M on half channel and 4 M on all channels
080 Increase acquisition memory to 16 M on half channel and 8 M on all channels.
160 Increase acquisition memory to 32 M on half channel and 16 M on all channels.
320 Increase acquisition memory to 64 M on half channel and 32 M on all channels.
640 Increase acquisition memory to 128 M on half channel and 64 M on all channels.
Note: Memory options are also available after oscilloscope purchase. See the "Customer-Installed Instrument
Options" heading in this table.
002 EZJIT Jitter Analysis Software
003 High-Speed Serial Data Analysis Software with Clock Recovery
006 My Infiniium Integration Package
007 Low-Speed Serial Data Analysis Software for I2C and SPI
008 CAN Serial Data Analysis Software
009 InfiniiScan Event Identification Software
017
≥40 GB Removable Hard Disk Drive. Available on new oscilloscope purchase only.
Replaces ≥40 GB internal hard disk drive with a ≥40 GB removable hard disk drive.
Order the N5422A for additional hard disk drive cartridges that contain the full
Windows operating system and oscilloscope application.
Customer-Installed
Instrument Options
N5407A-040 Increase acquisition memory to 8 M on half channel and 4 M on all channels
N5407A-080 Increase acquisition memory to 16 M on half channel and 8 M on all channels.
N5407A-160 Increase acquisition memory to 32 M on half channel and 16 M on all channels.
N5407A-320 Increase acquisition memory to 64 M on half channel and 32 M on all channels.
N5407A-640 Increase acquisition memory to 128 M on half channel and 64 M on all channels.
Note: Memory options installed after oscilloscope purchase do not require opening the oscilloscope case.
E2681A EZJIT Jitter Analysis Software
N5384A High-Speed Serial Data Analysis Software with Clock Recovery
E2699A My Infiniium Integration Package
N5391A Low-Speed Serial Data Analysis Software for I2C and SPI
- Service Guide 1
- In This Book 5
- Contents 7
- 6 Replacing Assemblies 8
- 7 Replaceable Parts 8
- 8 Theory of Operation 8
- General Information 10
- Accessories supplied 13
- Accessories available 14
- Options available 15
- ± 5°C from the temperature 16
- Environmental Conditions 17
- Measurement Category 17
- Oscilloscope Dimensions 18
- Preparing for Use 19
- Setting Up the Oscilloscope 20
- To inspect package contents 21
- Figure 2-1 21
- To connect power 22
- Attaching the Probe Connector 25
- Probing the Circuit 26
- To connect the digital probe 28
- Digital probe lead set 29
- 40-pin Connector Pinout 30
- Figure 2-14 31
- To turn on the oscilloscope 32
- To turn off the oscilloscope 32
- Probe Compensation 33
- To clean the oscilloscope 35
- Testing Performance 37
- Clear Display 39
- Averaging 39
- Specifications 39
- Performance Test Procedures 39
- Fluke MET/CAL Procedures 39
- To test the DC calibrator 40
- To test input resistance 42
- Connect the equipment 43
- Select Close 45
- (Supply) Minimum Maximum 45
- Set the scale from the 46
- Set the offset from the 46
- To test bandwidth 47
- To verify threshold accuracy 49
- Connections 50
- High-to-Low Transitions 55
- Threshold Voltage Setting V2 56
- Low-to-High Transitions 57
- To test time scale accuracy 59
- Oscilloscope 60
- Sine Wave Source 60
- Frequency Reference 60
- Agilent Technologies 64
- Range Supply Limits 65
- Performance Test Record 66
- Calibrating and Adjusting 67
- To run the self calibration 69
- Troubleshooting 71
- Default Setup 73
- 54830F01a 75
- Primary Trouble Isolation 76
- Run oscilloscope self-tests 77
- Self Calibration 78
- Performance” on page 37 78
- No Display Trouble Isolation 79
- Input Pin # 7 65432 1 81
- Replace any shorted assembly 84
- Replace the power supply 84
- To check probe power outputs 85
- To Check the keyboard 86
- To check the LEDs 87
- Intel D915GUX Motherboard 88
- To Reset 89
- 5 and 7 89
- To setup the BIOS 91
- Figure 5-12 93
- Software Revisions 94
- Replacing Assemblies 95
- Bottom sleeve fasteners 99
- Removing bottom sleeve 100
- Connecting Mylar flex sables 101
- Disconnecting W8 104
- Access Hole 105
- Removing the BNC nuts 108
- Figure 6-17 112
- Opening in side of 131
- Fan control board cables 131
- Acquisition board cables 131
- Figure 6-32 132
- Lift board out of chassis 134
- To remove and replace a fan 135
- Mylar flex cables 136
- T10 Torx Screws 136
- Replaceable Parts 137
- Power Cords 139
- Exploded Views 140
- Replaceable Parts List 145
- Theory of Operation 149
- Figure 8-1 150
- Logic Trigger 154
- Attenuator Theory 155
- Acquisition Theory 155
- • Trigger levels 156
Verwandte Produkte und Handbücher für Messen, Testen & Steuern Agilent Technologies 8000 Series
(92 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.062 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern