Agilent Technologies InfiniiVision 7000B Series Betriebsanweisung

Agilent Technologies Agilent InfiniiVision 5000/6000/7000 Series OscilloscopesUser’s Guide

Contents10 InfiniiVision Oscilloscopes User’s GuideTrigger Holdoff 90Trigger Holdoff Operating Hints 90To set holdoff 90External Trigger Input 922-Ch

4 Triggering100 InfiniiVision Oscilloscopes User’s Guide7 Press the Signals softkey to enter the CAN Signals Menu.8 Press the Source softkey to selec

Triggering 4InfiniiVision Oscilloscopes User’s Guide 101The CAN baud rate can be set to:The default baud rate is 1 Mb/s.If the desired baud rate is n

4 Triggering102 InfiniiVision Oscilloscopes User’s GuideDuration TriggerDuration trigger lets you define a pattern, then trigger on a specified time

Triggering 4InfiniiVision Oscilloscopes User’s Guide 103• X sets the pattern to don't care on the selected channel. Any channel set to don'

4 Triggering104 InfiniiVision Oscilloscopes User’s GuideWhen the duration trigger occursThe timer starts on the last edge that makes the pattern (log

Triggering 4InfiniiVision Oscilloscopes User’s Guide 105Edge TriggerThe Edge trigger type identifies a trigger by looking for a specified edge (slope

4 Triggering106 InfiniiVision Oscilloscopes User’s GuideYou can select analog channel 1 or 2, Ext, or Line as the trigger source on any Agilent Infin

Triggering 4InfiniiVision Oscilloscopes User’s Guide 107FlexRay Setup and TriggeringThe N5432C FlexRay triggering and decode option (Option FLX) requ

4 Triggering108 InfiniiVision Oscilloscopes User’s GuideIt is important to specify the correct bus because this setting affects CRC error detection.8

Triggering 4InfiniiVision Oscilloscopes User’s Guide 1095 Press the Frames softkey to access the FlexRay Frame Trigger Menu.6 Press the Frame ID soft

Contents InfiniiVision Oscilloscopes User’s Guide 11LIN Trigger 128MIL-STD 1553 Setup and Triggering 131Probing MIL-STD 1553 Signals 131Setup for MIL-

4 Triggering110 InfiniiVision Oscilloscopes User’s GuideTriggering on FlexRay Errors1 In the front panel Trigger section, press [More].2 In the More

Triggering 4InfiniiVision Oscilloscopes User’s Guide 1114 In the FlexRay Trigger Menu, press Trigger; then, select Event.5 Press Event; then, select

4 Triggering112 InfiniiVision Oscilloscopes User’s GuideGlitch or Narrow Pulse CaptureA glitch is a rapid change in the waveform that is usually narr

Triggering 4InfiniiVision Oscilloscopes User’s Guide 11315 ns Narrow Pulse, 20 ms/div, Peak Detect ModeUsing Peak Detect Mode to Find a Glitch1 Conne

4 Triggering114 InfiniiVision Oscilloscopes User’s Guide4 Characterize the glitch with Zoom mode:a Press the [Menu/Zoom] key (or [Main/Delayed] key o

Triggering 4InfiniiVision Oscilloscopes User’s Guide 115I2C TriggerAn I2C (Inter-IC bus) trigger setup consists of connecting the oscilloscope to the

4 Triggering116 InfiniiVision Oscilloscopes User’s GuideAs you press the SCL softkey (or rotate the Entry knob), the SCL label for the source channel

Triggering 4InfiniiVision Oscilloscopes User’s Guide 117• Stop Condition — The oscilloscope triggers when data (SDA) transitions from low to high whi

4 Triggering118 InfiniiVision Oscilloscopes User’s Guide• Frame (Start: Addr7: Read: Ack: Data) or Frame (Start: Addr7: Write: Ack: Data) — The oscil

Triggering 4InfiniiVision Oscilloscopes User’s Guide 119For triggering purposes, a restart is treated as a start condition.12 If you have set the osc

Contents12 InfiniiVision Oscilloscopes User’s Guide5 Displaying 173Tips for Displaying Waveforms 174Stabilizing the Display 174Interpreting the Displ

4 Triggering120 InfiniiVision Oscilloscopes User’s GuideIf don't care (0xXX) is selected for data, the data will be ignored. The trigger will al

Triggering 4InfiniiVision Oscilloscopes User’s Guide 121I2S Trigger The N5468A (Option SND) I²S trigger and serial decode option adds the ability to

4 Triggering122 InfiniiVision Oscilloscopes User’s Guide6 Press the Signals softkey to display the I2S Signals Menu. A diagram appears showing WS, SC

Triggering 4InfiniiVision Oscilloscopes User’s Guide 12310 Set the trigger levels for the SCLK, WS, and SDATA signals to the middle of the signals:•

4 Triggering124 InfiniiVision Oscilloscopes User’s Guide14 Press the Alignment softkey and rotate the Entry knob to select the desired alignment of t

Triggering 4InfiniiVision Oscilloscopes User’s Guide 12515 Press the WS Low softkey to select whether WS Low indicates Left or Right channel data. Th

4 Triggering126 InfiniiVision Oscilloscopes User’s Guide20 Press the Trigger softkey and choose a qualifier:• Equal — triggers on the specified audio

Triggering 4InfiniiVision Oscilloscopes User’s Guide 127• Decreasing value — similar to the description above except the trigger occurs on a descreas

4 Triggering128 InfiniiVision Oscilloscopes User’s GuideLIN TriggerLIN (Local Interconnect Network) trigger setup consists of connecting the oscillos

Triggering 4InfiniiVision Oscilloscopes User’s Guide 1295 Press the Signals softkey. The LIN Signals Menu will be displayed.6 Press the Source softke

Contents InfiniiVision Oscilloscopes User’s Guide 13Measurement Definitions 199Time Measurements 199Delay and Phase Measurements 203Voltage Measuremen

4 Triggering130 InfiniiVision Oscilloscopes User’s Guide10 Press the Sync Break softkey and select the minimum number of clocks that define a sync br

Triggering 4InfiniiVision Oscilloscopes User’s Guide 131MIL-STD 1553 Setup and TriggeringThe N5469A MIL-STD 1553 triggering and decode option (Option

4 Triggering132 InfiniiVision Oscilloscopes User’s GuideSetup for MIL-STD 1553 SignalsTo set up the oscilloscope for MIL-STD 1553 signals:1 In the fr

Triggering 4InfiniiVision Oscilloscopes User’s Guide 133MIL-STD 1553 TriggeringTo set up the oscilloscope to capture MIL-STD 1553 signals, see “Setup

4 Triggering134 InfiniiVision Oscilloscopes User’s Guide• The Bit Time softkey lets you select the bit time position.• The 01X softkey lets you set t

Triggering 4InfiniiVision Oscilloscopes User’s Guide 135Nth Edge Burst TriggerThe Nth Edge Burst trigger lets you trigger on the Nth edge of a burst

4 Triggering136 InfiniiVision Oscilloscopes User’s Guide3 Press the Slope softkey to specify the slope of the edge.4 Press the Idle softkey; then, tu

Triggering 4InfiniiVision Oscilloscopes User’s Guide 137Pattern TriggerThe Pattern trigger identifies a trigger condition by looking for a specified

4 Triggering138 InfiniiVision Oscilloscopes User’s Guide• 0 sets the pattern to zero (low) on the selected channel. A low is a voltage level that is

Triggering 4InfiniiVision Oscilloscopes User’s Guide 139Hex Bus Pattern TriggerYou can specify a bus value on which to trigger. To do this, first def

Contents14 InfiniiVision Oscilloscopes User’s GuideSaving Oscilloscope Data 247Selecting a Destination for Your Saved Data248Selecting a File Name 24

4 Triggering140 InfiniiVision Oscilloscopes User’s GuidePulse Width TriggerPulse Width (glitch) triggering sets the oscilloscope to trigger on a posi

Triggering 4InfiniiVision Oscilloscopes User’s Guide 141When triggering on a positive pulse, the trigger will occur on the high to low transition of

4 Triggering142 InfiniiVision Oscilloscopes User’s Guide• When the time range (><) qualifier is selected, the Entry knob sets the upper time ra

Triggering 4InfiniiVision Oscilloscopes User’s Guide 143Sequence TriggerSequence trigger lets you trigger the oscilloscope after finding a sequence o

4 Triggering144 InfiniiVision Oscilloscopes User’s GuideAs you set stage, term, and channel definitions for the sequence trigger, these settings will

Triggering 4InfiniiVision Oscilloscopes User’s Guide 145Define the “Find” Stage1 Press the Stage softkey and select Find:.Find: is the first stage in

4 Triggering146 InfiniiVision Oscilloscopes User’s Guide5 If you select an edge term, one channel must be set to a rising edge or a falling edge. All

Triggering 4InfiniiVision Oscilloscopes User’s Guide 1474 If you select a pattern term, each channel in the pattern must be set to a 1 (high), 0 (low

4 Triggering148 InfiniiVision Oscilloscopes User’s Guide• No Reset — Resets on the find condition.• Pattern 1 (or 2) Entered — A pattern is entered o

Triggering 4InfiniiVision Oscilloscopes User’s Guide 149Adjust the Trigger Level• For analog channels, adjust the trigger level for the selected anal

Contents InfiniiVision Oscilloscopes User’s Guide 15Accessing the Web Interface 280Browser Web Control 281Remote Front Panel 281Remote Programming 283

4 Triggering150 InfiniiVision Oscilloscopes User’s GuideSPI TriggerSerial Peripheral Interface (SPI) trigger setup consists of connecting the oscillo

Triggering 4InfiniiVision Oscilloscopes User’s Guide 151Assign Oscilloscope Channels to SPI SignalsThis explains how to assign oscilloscope channesl

4 Triggering152 InfiniiVision Oscilloscopes User’s Guide6 Press the Clock softkey or turn the Entry knob to select the channel connected to the SPI s

Triggering 4InfiniiVision Oscilloscopes User’s Guide 1538 Press the Data softkey or turn the Entry knob to select the channel that is connected to th

4 Triggering154 InfiniiVision Oscilloscopes User’s Guide• If the framing signal is set to CS (or ~CS), the first clock edge as defined, rising or fal

Triggering 4InfiniiVision Oscilloscopes User’s Guide 155Set Up the Bits in the Serial Data StringThis explains how to set up the number of bits in th

4 Triggering156 InfiniiVision Oscilloscopes User’s GuideTV TriggerTV triggering can be used to capture the complicated waveforms of most standard and

Triggering 4InfiniiVision Oscilloscopes User’s Guide 1572 Press the Source softkey and select any analog channel as the TV trigger source.The selecte

4 Triggering158 InfiniiVision Oscilloscopes User’s Guide4 Press the Standard softkey to set the TV standard.The oscilloscope supports triggering on t

Triggering 4InfiniiVision Oscilloscopes User’s Guide 1596 If you select a line # mode, press the Line # softkey, then rotate the Entry knob to select

Contents16 InfiniiVision Oscilloscopes User’s GuideLIN Serial Decode 314Interpreting LIN Decode 317Interpreting LIN Lister Data 319MIL-STD 1553 Seria

4 Triggering160 InfiniiVision Oscilloscopes User’s GuideTo trigger on a specific line of videoTV triggering requires greater than 1/2 division of syn

Triggering 4InfiniiVision Oscilloscopes User’s Guide 161To trigger on all sync pulsesTo quickly find maximum video levels, you could trigger on all s

4 Triggering162 InfiniiVision Oscilloscopes User’s Guide3 Press the Mode softkey and select Field1 or Field2.TRIGGERING ON FIELD 1To trigger on all f

Triggering 4InfiniiVision Oscilloscopes User’s Guide 163TRIGGERING ON ALL FIELDSTo trigger on odd or even fieldsTo check the envelope of your video s

4 Triggering164 InfiniiVision Oscilloscopes User’s GuideTRIGGERING ON COLOR FIELD 1 ALTERNATING WITH COLOR FIELD 3If a more detailed analysis is requ

Triggering 4InfiniiVision Oscilloscopes User’s Guide 165HALF-FIELD HOLDOFF TIMEUSING TV HOLDOFF TO SYNCHRONIZE TO COLOR FIELD 1 OR 3 (FIELD 1 MODE)St

4 Triggering166 InfiniiVision Oscilloscopes User’s GuideUART/RS232 TriggerTo trigger on a UART (Universal Asynchronous Receiver/Transmitter) signal c

Triggering 4InfiniiVision Oscilloscopes User’s Guide 1676 Press the Signals softkey to display the UART/RS232 Signals Menu.7 Connect an oscilloscope

4 Triggering168 InfiniiVision Oscilloscopes User’s Guide12 Press the up arrow softkey to return to the previous menu.13 Press the Base softkey to sel

Triggering 4InfiniiVision Oscilloscopes User’s Guide 16918 If Burst is selected, an idle time (1 s to 10 s) can be specified so that the oscilloscop

Contents InfiniiVision Oscilloscopes User’s Guide 1712 Controls and Connectors 351Front Panel 3525000/6000 Series Front Panel (4-channel) 3525000/600

4 Triggering170 InfiniiVision Oscilloscopes User’s GuideUSB TriggerUSB trigger will trigger on a Start of Packet (SOP), End of Packet (EOP) signal, R

Triggering 4InfiniiVision Oscilloscopes User’s Guide 171As you press the D+ or D– softkey (or rotate the Entry knob), the D+ and D– label for the sou

4 Triggering172 InfiniiVision Oscilloscopes User’s Guide

173Agilent InfiniiVision 5000/6000/7000 Series OscilloscopeUser’s Guide 5Displaying Tips for Displaying Waveforms 174Stabilizing the Display 174Inte

5 Displaying174 InfiniiVision Oscilloscopes User’s GuideTips for Displaying WaveformsThe easiest way to display waveforms is to connect the probes to

Displaying 5InfiniiVision Oscilloscopes User’s Guide 175Interpreting the DisplayThe oscilloscope display contains acquired waveforms, setup informati

5 Displaying176 InfiniiVision Oscilloscopes User’s GuideGraphic Symbols in Softkey MenusSoftkeys are the six keys directly below the display. The are

Displaying 5InfiniiVision Oscilloscopes User’s Guide 177AutoScalePress the [AutoScale] key to quickly display the input signals.How AutoScale worksAu

5 Displaying178 InfiniiVision Oscilloscopes User’s GuideEnabling Fast Debug AutoScaleThe Fast Debug option changes the behavior of [AutoScale] to let

Displaying 5InfiniiVision Oscilloscopes User’s Guide 179Pan and ZoomThe ability to pan (move horizontally) and zoom (expand or compress horizontally)

Contents18 InfiniiVision Oscilloscopes User’s GuideTo change the displayed size of the digital channels 379To switch a single channel on or off 379To

5 Displaying180 InfiniiVision Oscilloscopes User’s Guide3 Turn the Horizontal Position (Delay Time) knob () to pan horizontally and turn the channel’

Displaying 5InfiniiVision Oscilloscopes User’s Guide 181Amplitude Modulation with Noise Shown at 40% IntensityGrid IntensityTo adjust the grid (grati

5 Displaying182 InfiniiVision Oscilloscopes User’s GuideInfinite PersistenceWith infinite persistence, the oscilloscope updates the display with new

Displaying 5InfiniiVision Oscilloscopes User’s Guide 183Using LabelsYou can define labels and assign them to each analog input channel, or you can tu

5 Displaying184 InfiniiVision Oscilloscopes User’s GuideTo assign a predefined label to a channel1 Press the [Label] key.2 Press the Channel softkey,

Displaying 5InfiniiVision Oscilloscopes User’s Guide 185The channel does not have to be turned on to have a label assigned to it. If the channel is t

5 Displaying186 InfiniiVision Oscilloscopes User’s GuideTo load labels from a text file into the oscilloscope:1 Use a text editor to create each labe

Displaying 5InfiniiVision Oscilloscopes User’s Guide 187This will delete all user-defined labels from the library and set the labels in the library b

5 Displaying188 InfiniiVision Oscilloscopes User’s GuideThe oscilloscope turns vectors on whenever the acquisition system stops. Digital channels on

Displaying 5InfiniiVision Oscilloscopes User’s Guide 189AntialiasingAt slower sweep speeds, the sample rate is reduced and a proprietary display algo

Contents InfiniiVision Oscilloscopes User’s Guide 19Measurement Category 403Measurement Category 403Measurement Category Definitions 403Transient With

5 Displaying190 InfiniiVision Oscilloscopes User’s Guide

191Agilent InfiniiVision 5000/6000/7000 Series OscilloscopeUser’s Guide 6 Measurements and Math FunctionsList of Automatic Measurements 192Making Au

6 Measurements and Math Functions192 InfiniiVision Oscilloscopes User’s GuideList of Automatic MeasurementsYou can press the [Quick Meas] key and sel

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 193Preshoot and Overshoot• “Preshoot” on page 211.• “Overshoot” on page 212

6 Measurements and Math Functions194 InfiniiVision Oscilloscopes User’s Guide3 Press the Select softkey then rotate the Entry knob to select a measur

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 195The following statistics are shown: Name of the measurement, current mea

6 Measurements and Math Functions196 InfiniiVision Oscilloscopes User’s GuideTo reset the statistics measurements, press the Reset Statistics softkey

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 197Measurement ThresholdsSetting measurement thresholds defines the vertica

6 Measurements and Math Functions198 InfiniiVision Oscilloscopes User’s GuideIncreasing the lower value beyond the set middle value will automaticall

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 199Measurement DefinitionsTime MeasurementsThe default lower, middle, and u

Notices© Agilent Technologies, Inc. 2000-2011No part of this manual may be reproduced in any form or by any means (including elec-tronic storage and r

Contents20 InfiniiVision Oscilloscopes User’s Guide

6 Measurements and Math Functions200 InfiniiVision Oscilloscopes User’s GuideThe measured frequency is normally displayed in 5 digits, but can be dis

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 201ISOLATING AN EVENT FOR FREQUENCY MEASUREMENTPeriodPeriod is the time per

6 Measurements and Math Functions202 InfiniiVision Oscilloscopes User’s Guide+ Width+ Width is the time from the middle threshold of the rising edge

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 203Delay and Phase MeasurementsDelayDelay measures the time difference from

6 Measurements and Math Functions204 InfiniiVision Oscilloscopes User’s GuideThe example below shows a delay measurement between the rising edge of c

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 205The example below shows a phase measurement between the channel 1 and th

6 Measurements and Math Functions206 InfiniiVision Oscilloscopes User’s GuideThe following figure shows the voltage measurement points.AmplitudeThe A

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 207AverageAverage is the sum of the waveform samples divided by the number

6 Measurements and Math Functions208 InfiniiVision Oscilloscopes User’s GuidePeak-PeakThe peak-to-peak value is the difference between Maximum and Mi

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 209The following figure graphically shows the mean and standard deviation.

21Agilent InfiniiVision 5000/6000/7000 Series OscilloscopeUser’s Guide 1IntroductionModels Covered in this Manual 22Specifications and Characteristi

6 Measurements and Math Functions210 InfiniiVision Oscilloscopes User’s Guidewhere: = the standard deviation.N = the number of measurements taken.xi

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 211Overshoot and Preshoot MeasurementsPreshootPreshoot is distortion that p

6 Measurements and Math Functions212 InfiniiVision Oscilloscopes User’s GuideOvershootOvershoot is distortion that follows a major edge transition ex

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 213Post Acquisition ProcessingIn addition to changing display parameters af

6 Measurements and Math Functions214 InfiniiVision Oscilloscopes User’s GuideCursor MeasurementsCursors are horizontal and vertical markers that indi

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 215To make cursor measurements1 Connect a signal to the oscilloscope and ob

6 Measurements and Math Functions216 InfiniiVision Oscilloscopes User’s GuideManual and Track Waveform modes can be used on waveforms that are displa

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 217Cursor ExamplesCURSORS USED TO MEASURE PULSE WIDTHS OTHER THAN MIDDLE TH

6 Measurements and Math Functions218 InfiniiVision Oscilloscopes User’s GuideExpand the display with Zoom mode, then characterize the event of intere

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 219Press the X1 X2 softkey and move the cursors together to check for pulse

1 Introduction22 InfiniiVision Oscilloscopes User’s GuideAgilent InfiniiVision oscilloscopes feature MegaZoom III technology: • Most responsive deep

6 Measurements and Math Functions220 InfiniiVision Oscilloscopes User’s GuideXY Horizontal ModeThe XY horizontal mode converts the oscilloscope from

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 221SIGNAL CENTERED ON THE DISPLAY4 Press the [Cursors] key.5 Set the Y2 cur

6 Measurements and Math Functions222 InfiniiVision Oscilloscopes User’s Guide6 Move the Y1 and Y2 cursors to the intersection of the signal and the Y

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 223SIGNALS ARE 90 OUT OF PHASESIGNALS ARE IN PHASE

6 Measurements and Math Functions224 InfiniiVision Oscilloscopes User’s GuideMath FunctionsMath functions can be performed on analog channels. The re

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 225To perform a math function upon an arithmetic operationTo perform a func

6 Measurements and Math Functions226 InfiniiVision Oscilloscopes User’s GuideUnitsUnits for each input channel can be set to Volts or Amps using the

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 227MultiplyWhen you select the multiply math function, the voltage values o

6 Measurements and Math Functions228 InfiniiVision Oscilloscopes User’s GuideAdd or SubtractWhen you select add or subtract, the Source 1 and Source

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 229EXAMPLE OF SUBTRACTChannel 1Channel 21 – 2 waveform Subtraction operator

Introduction 1InfiniiVision Oscilloscopes User’s Guide 23Specifications and CharacteristicsPlease see the InfiniiVision oscilloscope data sheets for

6 Measurements and Math Functions230 InfiniiVision Oscilloscopes User’s GuideDifferentiated/dt (differentiate) calculates the discrete time derivativ

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 231EXAMPLE OF DIFFERENTIATE FUNCTION Channel 1d/dt waveform Differentiate o

6 Measurements and Math Functions232 InfiniiVision Oscilloscopes User’s GuideIntegrate dt (integrate) calculates the integral of the selected source

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 233INTEGRATE AND SIGNAL OFFSETChannel 1dt waveform Channel 1dt waveform

6 Measurements and Math Functions234 InfiniiVision Oscilloscopes User’s GuideSquare RootSquare root () calculates the square root of the selected so

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 235EXAMPLE OF  (SQUARE ROOT).Channel 1 waveform Square root operatorSourc

6 Measurements and Math Functions236 InfiniiVision Oscilloscopes User’s GuideFFT MeasurementFFT is used to compute the fast Fourier transform using a

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 237The following figure illustrates aliasing. This is the spectrum of a 990

6 Measurements and Math Functions238 InfiniiVision Oscilloscopes User’s GuideFFT Operation1 Press the [Math] key, press the Function softkey and sele

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 239• Rectangular — good frequency resolution and amplitude accuracy, but us

1 Introduction24 InfiniiVision Oscilloscopes User’s GuideLicensed Options Many of the following licensed options can be easily installed without retu

6 Measurements and Math Functions240 InfiniiVision Oscilloscopes User’s GuideYou can make peak-to-peak, maximum, minimum, and average dB measurements

Measurements and Math Functions 6InfiniiVision Oscilloscopes User’s Guide 241number of points in the FFT. The actual resolution of the display will n

6 Measurements and Math Functions242 InfiniiVision Oscilloscopes User’s GuideEnabling Precision Measurements and MathNormally, after pressing [Save/R

243Agilent InfiniiVision 5000/6000/7000 Series OscilloscopeUser’s Guide 7Printing and SavingPrinting the Oscilloscope’s Display 244Quick Print 244To

7 Printing and Saving244 InfiniiVision Oscilloscopes User’s GuidePrinting the Oscilloscope’s DisplayYou can print the complete display, including the

Printing and Saving 7InfiniiVision Oscilloscopes User’s Guide 245To print the oscilloscope’s display1 Connect a USB printer to either the USB port on

7 Printing and Saving246 InfiniiVision Oscilloscopes User’s Guide• Form Feed — The Form Feed option can be selected to send a form feed command to th

Printing and Saving 7InfiniiVision Oscilloscopes User’s Guide 247Saving Oscilloscope DataHere are a few points about saving oscilloscope data:• You c

7 Printing and Saving248 InfiniiVision Oscilloscopes User’s GuideSelecting a Destination for Your Saved DataPress [Save/Recall]&Save to access th

Printing and Saving 7InfiniiVision Oscilloscopes User’s Guide 249If one or more USB mass storage devices are connected to the oscilloscope, you can n

Introduction 1InfiniiVision Oscilloscopes User’s Guide 25See also “Installed Licenses” on page 400.LSS I2C/SPI serial decode option (for 4 channel or

7 Printing and Saving250 InfiniiVision Oscilloscopes User’s Guide4 You can press the Delete Character softkey to delete the current character and shi

Printing and Saving 7InfiniiVision Oscilloscopes User’s Guide 251• ASCII XY data file— This creates a file of comma-separated variables for each disp

7 Printing and Saving252 InfiniiVision Oscilloscopes User’s GuideThe Invert Graticule Colors option can be used to reduce the amount of black ink it

Printing and Saving 7InfiniiVision Oscilloscopes User’s Guide 253The length control has no effect on the amount of Serial Decode data saved; all seri

7 Printing and Saving254 InfiniiVision Oscilloscopes User’s GuideFormat (ALB data file format settings in Save Menu)You can acquire data from the osc

Printing and Saving 7InfiniiVision Oscilloscopes User’s Guide 255RECOMMENDED SIGNAL MAPPINGTo save a waveform and/or setup to a USB mass storage devi

7 Printing and Saving256 InfiniiVision Oscilloscopes User’s GuideTo save a waveform and/or setup to the oscilloscope’s internal memory1 Press the [Sa

Printing and Saving 7InfiniiVision Oscilloscopes User’s Guide 257File Explorer The File Explorer lets you navigate the file system. Using the File Ex

7 Printing and Saving258 InfiniiVision Oscilloscopes User’s GuideSystem software System software files can be loaded into the oscilloscope. These sof

Printing and Saving 7InfiniiVision Oscilloscopes User’s Guide 259Navigate using Entry knob, select using this key or push Entry knobLoad selected fil

1 Introduction26 InfiniiVision Oscilloscopes User’s GuideNotesBuilt-in Quick HelpA Quick Help system is built into the oscilloscope. Press and hold a

7 Printing and Saving260 InfiniiVision Oscilloscopes User’s Guide

261Agilent InfiniiVision 5000/6000/7000 Series OscilloscopeUser’s Guide 8Acquisition ModesTo start and stop an acquisition 262To make a single acqui

8 Acquisition Modes262 InfiniiVision Oscilloscopes User’s GuideTo start and stop an acquisition• When you press the [Run/Stop] key, it illuminates in

Acquisition Modes 8InfiniiVision Oscilloscopes User’s Guide 263Memory Depth/Record Length[Run/Stop] versus [Single]When the oscilloscope is running,

8 Acquisition Modes264 InfiniiVision Oscilloscopes User’s GuideTo make a single acquisitionWhen you press the [Single] key it illuminates in yellow a

Acquisition Modes 8InfiniiVision Oscilloscopes User’s Guide 265Acquisition ModesThe InfiniiVision oscilloscopes have the following acquisition modes:

8 Acquisition Modes266 InfiniiVision Oscilloscopes User’s GuidePeak Detect ModeIn Peak Detect mode at slower sweep speeds, minimum and maximum sample

Acquisition Modes 8InfiniiVision Oscilloscopes User’s Guide 267Averaging ModeThe Averaging mode lets you average multiple acquisitions together to re

8 Acquisition Modes268 InfiniiVision Oscilloscopes User’s GuideRANDOM NOISE ON THE DISPLAYED WAVEFORM128 AVERAGES USED TO REDUCE RANDOM NOISESee also

Acquisition Modes 8InfiniiVision Oscilloscopes User’s Guide 269Realtime Sampling OptionRealtime sampling specifies that the oscilloscope produce the

27Agilent InfiniiVision 5000/6000/7000 Series OscilloscopeUser’s Guide 2Initial SetupPackage Contents 285000 Series Oscilloscope Package Contents 29

8 Acquisition Modes270 InfiniiVision Oscilloscopes User’s GuideTo see the sample rate, press the [Acquire] key on the front panel. The sample rate is

Acquisition Modes 8InfiniiVision Oscilloscopes User’s Guide 271Segmented MemoryYou can purchase the oscilloscope with the segmented memory option fac

8 Acquisition Modes272 InfiniiVision Oscilloscopes User’s GuideIf the signal you are measuring has more than about 1 s of “dead time” (inactivity), c

Acquisition Modes 8InfiniiVision Oscilloscopes User’s Guide 273Measurements, statistics, and infinite persistenceTo perform measurements and view sta

8 Acquisition Modes274 InfiniiVision Oscilloscopes User’s GuideSaving data from segmented memoryYou can save either the currently displayed segment (

275Agilent InfiniiVision 5000/6000/7000 Series OscilloscopeUser’s Guide 9Web InterfaceSetting up the Oscilloscope’s LAN Connection 276Accessing the

9 Web Interface276 InfiniiVision Oscilloscopes User’s GuideMicrosoft Internet Explorer is the recommended Web browser for communication and control o

Web Interface 9InfiniiVision Oscilloscopes User’s Guide 277To connect to the network using Manual mode1 Get the oscilloscope’s network parameters (ho

9 Web Interface278 InfiniiVision Oscilloscopes User’s Guide4 Open a web browser and enter the oscilloscope’s hostname in the address field. The oscil

Web Interface 9InfiniiVision Oscilloscopes User’s Guide 279After the LAN connection is configured, you can find the oscilloscope’s IP address and use

2 Initial Setup28 InfiniiVision Oscilloscopes User’s GuidePackage Contents✔ Inspect the shipping container for damage.If your shipping container appe

9 Web Interface280 InfiniiVision Oscilloscopes User’s GuideAccessing the Web InterfaceTo access the oscilloscope’s web interface:1 Connect the oscill

Web Interface 9InfiniiVision Oscilloscopes User’s Guide 281Browser Web ControlThe web interface’s Browser Web Control page gives you access to the Re

9 Web Interface282 InfiniiVision Oscilloscopes User’s GuideScrolling and Monitor ResolutionWhen using a monitor resolution of 1024 x 768 or less on t

Web Interface 9InfiniiVision Oscilloscopes User’s Guide 283Remote ProgrammingTo send remote programming commands to the oscilloscope via the SCPI Com

9 Web Interface284 InfiniiVision Oscilloscopes User’s GuideIf you get the “Unable to connect to the instrument. You may need to set the instrument’s

Web Interface 9InfiniiVision Oscilloscopes User’s Guide 285Get ImageTo save (or print) the oscilloscope’s display from the web interface:1 Access the

9 Web Interface286 InfiniiVision Oscilloscopes User’s GuideIdentification FunctionThe Identification web interface feature is useful when trying to l

Web Interface 9InfiniiVision Oscilloscopes User’s Guide 287Instrument UtilitiesThe Instrument Utilities page of the web interface lets you:• View ins

9 Web Interface288 InfiniiVision Oscilloscopes User’s GuideSetting a PasswordWhenever you connect the oscilloscope to a LAN, it is good practice to s

Web Interface 9InfiniiVision Oscilloscopes User’s Guide 2894 Enter your desired password, and click Apply Changes.When accessing the password protect

Initial Setup 2InfiniiVision Oscilloscopes User’s Guide 295000 Series Oscilloscope Package ContentsInfiniiVision 5000 Series OscilloscopeOscilloscope

9 Web Interface290 InfiniiVision Oscilloscopes User’s Guide

291Agilent InfiniiVision 5000/6000/7000 Series OscilloscopeUser’s Guide 10Serial Decode/ListerSerial Decode 292Lister 293CAN Serial Decode 295FlexRa

10 Serial Decode/Lister292 InfiniiVision Oscilloscopes User’s GuideSerial DecodeAgilent’s hardware accelerated serial decode options can be installed

Serial Decode/Lister 10InfiniiVision Oscilloscopes User’s Guide 293ListerLister is a powerful tool for investigating protocol failures. You can use L

10 Serial Decode/Lister294 InfiniiVision Oscilloscopes User’s Guide4 Press the [Single] key (in the Run Control group on the front panel) to stop the

Serial Decode/Lister 10InfiniiVision Oscilloscopes User’s Guide 295CAN Serial Decode1 Connect the CAN signal to one of the oscilloscope’s input chann

10 Serial Decode/Lister296 InfiniiVision Oscilloscopes User’s Guide4 Specify the CAN signal:a Press the Settings softkey to access the CAN Signals Me

Serial Decode/Lister 10InfiniiVision Oscilloscopes User’s Guide 297The value of the trigger level or digital threshold is displayed in the upper-righ

10 Serial Decode/Lister298 InfiniiVision Oscilloscopes User’s Guide10 If the decode line does not appear on the display, press the Decode softkey to

Serial Decode/Lister 10InfiniiVision Oscilloscopes User’s Guide 299• Data length code (DLC) appears in blue for data frames and green for remote fram

InfiniiVision Oscilloscopes User’s Guide 3Book MapInitial Setup Connecting to the Device Under TestTriggeringDisplaying Measurements and Math Functio

2 Initial Setup30 InfiniiVision Oscilloscopes User’s Guide6000A Series Oscilloscope Package ContentsPower cord(Based on country of origin)6000A Serie

10 Serial Decode/Lister300 InfiniiVision Oscilloscopes User’s GuideCounters• The FRAMES counter gives the total number of completed remote, data, ove

Serial Decode/Lister 10InfiniiVision Oscilloscopes User’s Guide 301Interpreting CAN Lister DataIn addition to the standard Time column, the CAN Liste

10 Serial Decode/Lister302 InfiniiVision Oscilloscopes User’s GuideFlexRay Serial DecodeTo set up the oscilloscope to capture FlexRay signals, see “S

Serial Decode/Lister 10InfiniiVision Oscilloscopes User’s Guide 303Interpreting FlexRay Frame DecodeThe FlexRay decode display shows frame decoding.•

10 Serial Decode/Lister304 InfiniiVision Oscilloscopes User’s GuideFlexRay TotalizerThe FlexRay totalizer consists of counters that provide a direct

Serial Decode/Lister 10InfiniiVision Oscilloscopes User’s Guide 305Interpreting FlexRay Lister DataIn addition to the standard Time column, the FlexR

10 Serial Decode/Lister306 InfiniiVision Oscilloscopes User’s GuideI2C Serial Decode1 Select the I2C serial decode mode:a Press the [Acquire] key.b P

Serial Decode/Lister 10InfiniiVision Oscilloscopes User’s Guide 307a Press the Settings softkey to access the I2C Signals Menu.b Press the SCL softke

10 Serial Decode/Lister308 InfiniiVision Oscilloscopes User’s GuideInterpreting I2C Decode• Angled waveforms show an active bus (inside a packet/fram

Serial Decode/Lister 10InfiniiVision Oscilloscopes User’s Guide 309• Aliased bus values (undersampled or indeterminate) are drawn in red.• Unknown bu

Initial Setup 2InfiniiVision Oscilloscopes User’s Guide 316000A Option BAT Oscilloscope Package ContentsAC/DC power adapterFront-panel cover6000A Ser

10 Serial Decode/Lister310 InfiniiVision Oscilloscopes User’s GuideI2S Serial Decode1 Select the I2S serial decode mode:a Press the [Acquire] key.b P

Serial Decode/Lister 10InfiniiVision Oscilloscopes User’s Guide 3112 Press the Settings softkey to open the I2S Settings Menu.a Press the Signals sof

10 Serial Decode/Lister312 InfiniiVision Oscilloscopes User’s GuideInterpreting I2S Decode• Angled waveforms show an active bus (inside a packet/fram

Serial Decode/Lister 10InfiniiVision Oscilloscopes User’s Guide 313Interpreting I2S Lister DataIn addition to the standard Time column, the I2S Liste

10 Serial Decode/Lister314 InfiniiVision Oscilloscopes User’s GuideLIN Serial Decode1 Select the LIN serial decode mode:a Press the [Acquire] key.b P

Serial Decode/Lister 10InfiniiVision Oscilloscopes User’s Guide 3153 Specify the LIN signal:a Press the Settings softkey to access the LIN Signals Me

10 Serial Decode/Lister316 InfiniiVision Oscilloscopes User’s GuideIf the desired baud rate is not shown in the list, select User Defined. You can se

Serial Decode/Lister 10InfiniiVision Oscilloscopes User’s Guide 3175 If the oscilloscope is stopped, press the [Run/Stop] key to acquire and decode d

10 Serial Decode/Lister318 InfiniiVision Oscilloscopes User’s Guide• For LIN 1.3, the checksum appears in blue if correct, or red if incorrect. The c

Serial Decode/Lister 10InfiniiVision Oscilloscopes User’s Guide 319Interpreting LIN Lister DataIn addition to the standard Time column, the LIN Liste

2 Initial Setup32 InfiniiVision Oscilloscopes User’s Guide6000L Series Oscilloscope Package Contents6000L Series OscilloscopeOscilloscope Probes10073

10 Serial Decode/Lister320 InfiniiVision Oscilloscopes User’s GuideMIL-STD 1553 Serial DecodeTo probe MIL-STD 1553 signals, see “Probing MIL-STD 1553

Serial Decode/Lister 10InfiniiVision Oscilloscopes User’s Guide 321Interpreting MIL-STD 1553 DecodeTo display serial decode information, you must pre

10 Serial Decode/Lister322 InfiniiVision Oscilloscopes User’s GuideViewing MIL-STD 1553 Data in the Lister1 In the Serial Decode Menu (when serial de

Serial Decode/Lister 10InfiniiVision Oscilloscopes User’s Guide 323SPI Serial Decode1 Select the SPI serial decode mode:a Press the [Acquire] key.b P

10 Serial Decode/Lister324 InfiniiVision Oscilloscopes User’s Guide2 Specify the SPI signals:a Press the Settings softkey to access the SPI Settings

Serial Decode/Lister 10InfiniiVision Oscilloscopes User’s Guide 325c Press the Clock softkey, and use the Entry knob to select the channel probing th

10 Serial Decode/Lister326 InfiniiVision Oscilloscopes User’s GuideIf you have connected one of the oscilloscope’s digital source channels to the Clo

Serial Decode/Lister 10InfiniiVision Oscilloscopes User’s Guide 327You can use the Zoom horizontal sweep mode for easier navigation of the acquired d

10 Serial Decode/Lister328 InfiniiVision Oscilloscopes User’s Guide• Red dots in the decode line indicate that there is data that is not being displa

Serial Decode/Lister 10InfiniiVision Oscilloscopes User’s Guide 329UART/RS232 Serial Decode1 Select the UART/RS232 serial decode mode:a Press the [Ac

Initial Setup 2InfiniiVision Oscilloscopes User’s Guide 337000A Series Oscilloscope Package ContentsPower cord(Based on country of origin)*Digital Pr

10 Serial Decode/Lister330 InfiniiVision Oscilloscopes User’s Guide2 Specify the UART/RS232 signals:a Press the Settings softkey to access the UART/R

Serial Decode/Lister 10InfiniiVision Oscilloscopes User’s Guide 331b Press the Signals softkey, and select the oscilloscope channels that you have co

10 Serial Decode/Lister332 InfiniiVision Oscilloscopes User’s Guide8 Make sure the trigger or threshold levels are set to the middle of the signals:•

Serial Decode/Lister 10InfiniiVision Oscilloscopes User’s Guide 333Interpreting UART/RS232 Decode• Angled waveforms show an active bus (inside a pack

10 Serial Decode/Lister334 InfiniiVision Oscilloscopes User’s Guide• A parity error will cause the associated data word to be shown in red, which inc

Serial Decode/Lister 10InfiniiVision Oscilloscopes User’s Guide 335Interpreting UART/RS232 Lister DataIn addition to the standard Time column, the UA

10 Serial Decode/Lister336 InfiniiVision Oscilloscopes User’s Guide

337Agilent InfiniiVision 5000/6000/7000 Series OscilloscopeUser’s Guide 11Mask TestTo create a mask from a “golden” waveform (Automask) 338Setup Opt

11 Mask Test338 InfiniiVision Oscilloscopes User’s GuideTo create a mask from a “golden” waveform (Automask)A golden waveform meets all chosen parame

Mask Test 11InfiniiVision Oscilloscopes User’s Guide 3397 Press the Create Mask softkey. The mask is created and testing begins. Whenever the Create

2 Initial Setup34 InfiniiVision Oscilloscopes User’s GuideAccessories Available Model DescriptionN2918A 6000/7000 Series Oscilloscope Evaluation KitN

11 Mask Test340 InfiniiVision Oscilloscopes User’s GuideSetup OptionsRun UntilThe Run Until softkey lets you specify a condition on which to terminat

Mask Test 11InfiniiVision Oscilloscopes User’s Guide 341Save The oscilloscope will save the screen image based on the settings you have chosen. See “

11 Mask Test342 InfiniiVision Oscilloscopes User’s GuideMask Test Trigger OutputThe oscilloscope’s trigger output (located on the rear panel) can be

Mask Test 11InfiniiVision Oscilloscopes User’s Guide 343Mask StatisticsFrom the Mask Test Menu, press the Statistics softkey to enter the Mask Statis

11 Mask Test344 InfiniiVision Oscilloscopes User’s GuideReset StatisticsPress this softkey to reset the statistics counters to zero. Note that statis

Mask Test 11InfiniiVision Oscilloscopes User’s Guide 345To manually modify a mask fileYou can manually modify a mask file that you created using the

11 Mask Test346 InfiniiVision Oscilloscopes User’s GuideMask Violation RegionsUp to 8 regions can be defined for a mask. They can be numbered 1-8. Th

Mask Test 11InfiniiVision Oscilloscopes User’s Guide 347• X• Y1• Y2These four parameters are defined in the Oscilloscope Setup portion of the mask f

11 Mask Test348 InfiniiVision Oscilloscopes User’s GuideBuilding a Mask FileThe following mask uses all eight regions. The most difficult part of cre

Mask Test 11InfiniiVision Oscilloscopes User’s Guide 349 -12.50, 1.500/* Region Number */ 3/* Number of vertices */ 6 -05.00, 1.000 -02

Initial Setup 2InfiniiVision Oscilloscopes User’s Guide 35W2637A LPDDR BGA probe, x16, 404 MHz, 100 ohm input impedanceW2638A LPDDR BGA probe, x32, 4

11 Mask Test350 InfiniiVision Oscilloscopes User’s Guide/* Number of vertices */ 4 -12.50, MIN -10.00, -1.750 10.00, -1.750 12.5

351Agilent InfiniiVision 5000/6000/7000 Series OscilloscopeUser’s Guide 12Controls and ConnectorsFront Panel 3525000/6000 Series Front Panel (4-chan

12 Controls and Connectors352 InfiniiVision Oscilloscopes User’s GuideFront Panel5000/6000 Series Front Panel (4-channel) Click the text for the item

Controls and Connectors 12InfiniiVision Oscilloscopes User’s Guide 3535000/6000 Series Front Panel (2-Channel, differences only)The differences betwe

12 Controls and Connectors354 InfiniiVision Oscilloscopes User’s Guide6000L Series Front and Rear PanelClick the text for the item’s description and

Controls and Connectors 12InfiniiVision Oscilloscopes User’s Guide 3557000 Series Front Panel (4-Channel) Click the text for the item’s description a

12 Controls and Connectors356 InfiniiVision Oscilloscopes User’s Guide7000 Series Front Panel (2-Channel, differences only)The differences between th

Controls and Connectors 12InfiniiVision Oscilloscopes User’s Guide 357Front Panel Control and Connector Descriptions1. Power Switch Press once to swi

12 Controls and Connectors358 InfiniiVision Oscilloscopes User’s Guide6. [Math] Key The [Math] key provides access to add, subtract, multiply, differ

Controls and Connectors 12InfiniiVision Oscilloscopes User’s Guide 359If a trace is repositioned over an existing trace the indicator at the left edg

2 Initial Setup36 InfiniiVision Oscilloscopes User’s GuideYou can find these items at www.agilent.com or at www.parts.agilent.com.For information on

12 Controls and Connectors360 InfiniiVision Oscilloscopes User’s Guide18. Horizontal ControlsHorizontal Sweep Speed Control Turn the knob in the Hori

Controls and Connectors 12InfiniiVision Oscilloscopes User’s Guide 36122. Measure Keys Press the [Cursors] key to turn on cursors that you can use fo

12 Controls and Connectors362 InfiniiVision Oscilloscopes User’s GuideRear Panel5000 Series Rear Panel (4-Channel)Click the text for the item’s descr

Controls and Connectors 12InfiniiVision Oscilloscopes User’s Guide 3635000 Series Rear Panel (2-Channel)The 2-channel model rear panel is the same as

12 Controls and Connectors364 InfiniiVision Oscilloscopes User’s Guide6000 Series Rear Panel (4-Channel) Click the text for the item’s description an

Controls and Connectors 12InfiniiVision Oscilloscopes User’s Guide 3656000 Series Rear Panel (2-Channel)The 2-channel model rear panel is the same as

12 Controls and Connectors366 InfiniiVision Oscilloscopes User’s Guide6000 Series Option BAT Rear Panel (4-Channel)Click the text for the item’s desc

Controls and Connectors 12InfiniiVision Oscilloscopes User’s Guide 3677000 Series Rear Panel (4-Channel) Click the text for the item’s description an

12 Controls and Connectors368 InfiniiVision Oscilloscopes User’s Guide7000 Series Rear Panel (2-Channel)The 2-channel model rear panel is the same as

Controls and Connectors 12InfiniiVision Oscilloscopes User’s Guide 369Rear Panel Control and Connector Descriptions1. External Trigger Input See “Ext

Initial Setup 2InfiniiVision Oscilloscopes User’s Guide 37The tilt tabs (underneath the oscilloscope) can be positioned as shown in the center pictur

12 Controls and Connectors370 InfiniiVision Oscilloscopes User’s Guide13. Ground Terminal Option BAT oscilloscopes: Connect the oscilloscope to earth

371Agilent InfiniiVision 5000/6000/7000 Series OscilloscopeUser’s Guide 13Digital ChannelsTo connect the digital probes to the device under test 372

13 Digital Channels372 InfiniiVision Oscilloscopes User’s GuideTo connect the digital probes to the device under testThe digital channels are enabled

Digital Channels 13InfiniiVision Oscilloscopes User’s Guide 3734 Connect the ground lead on each set of channels (each pod), using a probe grabber. T

13 Digital Channels374 InfiniiVision Oscilloscopes User’s Guide6 Connect the grabber to a node in the circuit you want to test.7 For high-speed signa

Digital Channels 13InfiniiVision Oscilloscopes User’s Guide 3758 Repeat steps 3 through 6 until you have connected all points of interest. Acquiring

13 Digital Channels376 InfiniiVision Oscilloscopes User’s GuideTo display digital channels using AutoScaleWhen signals are connected to the digital c

Digital Channels 13InfiniiVision Oscilloscopes User’s Guide 377the instrument to the factory default configuration by pressing the [Save/Recall] key,

13 Digital Channels378 InfiniiVision Oscilloscopes User’s GuideInterpreting the digital waveform displayThe following figure shows a typical display

Digital Channels 13InfiniiVision Oscilloscopes User’s Guide 379To change the displayed size of the digital channels1 Press the [D15-D0] key.2 Press t

2 Initial Setup38 InfiniiVision Oscilloscopes User’s Guide2 Without releasing the hubs, rotate the handle to the desired position. Then release the h

13 Digital Channels380 InfiniiVision Oscilloscopes User’s GuideTo change the logic threshold for digital channels1 Press the [D15-D0] key so that the

Digital Channels 13InfiniiVision Oscilloscopes User’s Guide 381If a trace is repositioned over an existing trace the indicator at the left edge of th

13 Digital Channels382 InfiniiVision Oscilloscopes User’s GuideThe buses are shown at the bottom of the display.Using cursors to read bus valuesTo re

Digital Channels 13InfiniiVision Oscilloscopes User’s Guide 3834 Use the Entry knob and the X1 and X2 softkeys to position the cursors where you want

13 Digital Channels384 InfiniiVision Oscilloscopes User’s GuideBus values are displayed when using Pattern triggerThe bus values are also displayed w

Digital Channels 13InfiniiVision Oscilloscopes User’s Guide 385Digital channel signal fidelity: Probe impedance and groundingWhen using the mixed-sig

13 Digital Channels386 InfiniiVision Oscilloscopes User’s GuideHIGH-FREQUENCY PROBE EQUIVALENT CIRCUIT The impedance plots for the two models are sho

Digital Channels 13InfiniiVision Oscilloscopes User’s Guide 387Probe GroundingA probe ground is the low-impedance path for current to return to the s

13 Digital Channels388 InfiniiVision Oscilloscopes User’s Guidereconstructed waveforms, they do not show ringing and perturbations. You will not find

Digital Channels 13InfiniiVision Oscilloscopes User’s Guide 389To replace digital probe leadsIf you need to remove a probe lead from the cable, inser

Initial Setup 2InfiniiVision Oscilloscopes User’s Guide 393 Rock the oscilloscope back so that it rests securely on its feet.To retract the feet1 Til

13 Digital Channels390 InfiniiVision Oscilloscopes User’s Guide

391Agilent InfiniiVision 5000/6000/7000 Series OscilloscopeUser’s Guide 14UtilitiesTo restore the oscilloscope to its default configuration 392To pe

14 Utilities392 InfiniiVision Oscilloscopes User’s GuideTo restore the oscilloscope to its default configuration• Press the [Save/Recall] key, then p

Utilities 14InfiniiVision Oscilloscopes User’s Guide 393To perform service functions• Press the [Utility]&Service to display the Service Menu.The

14 Utilities394 InfiniiVision Oscilloscopes User’s GuideUser CalibrationPerform user-calibration:• Each year or after 2000 hours of operation.• If th

Utilities 14InfiniiVision Oscilloscopes User’s Guide 395For a 2-channel oscilloscope, connect a BNC tee to the equal length cables. Then connect a BN

14 Utilities396 InfiniiVision Oscilloscopes User’s Guide3 Connect a BNC cable (40 inches maximum) from the TRIG OUT connector on the rear panel to th

Utilities 14InfiniiVision Oscilloscopes User’s Guide 397Self TestPressing [Utility]&Service&Start Self Test performs a series of internal pro

14 Utilities398 InfiniiVision Oscilloscopes User’s Guide

399Agilent InfiniiVision 5000/6000/7000 Series OscilloscopeUser’s Guide 15ReferenceAbout Oscilloscope 400Software and Firmware Updates 400Installed

4 InfiniiVision Oscilloscopes User’s GuideIn This User’s Guide…This guide shows you how to use the InfiniiVision 5000/6000/7000 Series oscilloscopes.

2 Initial Setup40 InfiniiVision Oscilloscopes User’s GuideTo install the optional front panel overlay5000 Series OverlayWhen Option AB0 (Traditional

15 Reference400 InfiniiVision Oscilloscopes User’s GuideAbout OscilloscopePress [Utility]&Service&About Oscilloscope to display information a

Reference 15InfiniiVision Oscilloscopes User’s Guide 401•LSS — Low Speed Serial Decode. This license provides serial decode of I2C and SPI buses.•mem

15 Reference402 InfiniiVision Oscilloscopes User’s GuideSecure Environment Mode OptionSecure environment mode is compliant to National Industrial Sec

Reference 15InfiniiVision Oscilloscopes User’s Guide 403Measurement CategoryMeasurement CategoryThe InfiniiVision oscilloscopes are intended to be us

15 Reference404 InfiniiVision Oscilloscopes User’s GuideTransient Withstand CapabilityCAUTIONMaximum input voltage at analog inputs and 2-channel ext

Reference 15InfiniiVision Oscilloscopes User’s Guide 405Environmental ConditionsEnvironment Indoor use only.Ambient temperature Operating –10 °C to

15 Reference406 InfiniiVision Oscilloscopes User’s GuideUsing the 10 MHz reference clockThe 10 MHz REF BNC connector on the rear panel is provided so

Reference 15InfiniiVision Oscilloscopes User’s Guide 407A black locked padlock icon will appear at the top of the display.If the externally supplied

15 Reference408 InfiniiVision Oscilloscopes User’s GuideTo synchronize the timebase of two or more instrumentsThe oscilloscope can output it’s 10 MHz

Reference 15InfiniiVision Oscilloscopes User’s Guide 409Binary Data (.bin) FormatThe binary data format stores waveform data in binary format and pro

Initial Setup 2InfiniiVision Oscilloscopes User’s Guide 416000 Series OverlayLarge label: Remove the protective backing to expose the adhesive, align

15 Reference410 InfiniiVision Oscilloscopes User’s GuideAgilent provides the .m files, which need to be copied into the work directory for MATLAB. Th

Reference 15InfiniiVision Oscilloscopes User’s Guide 411Number of Waveform Buffers A 32-bit integer that is the number of waveform buffers required t

15 Reference412 InfiniiVision Oscilloscopes User’s GuideY Units A 32-bit integer that identifies the unit of measure for Y values in the acquired dat

Reference 15InfiniiVision Oscilloscopes User’s Guide 413Buffer Size A 32-bit integer that is the size of the buffer required to hold the data points.

15 Reference414 InfiniiVision Oscilloscopes User’s GuideExamples of Binary FilesSingle Acquisition Multiple Analog ChannelsThe following picture show

Reference 15InfiniiVision Oscilloscopes User’s Guide 415Single Acquisition All Pods Logic ChannelsThe following picture shows a binary file of a sing

15 Reference416 InfiniiVision Oscilloscopes User’s GuideFile Header12 bytesWaveform Header 1140 bytesWaveform DataHeader 112 bytesVoltage Data 1buffe

Reference 15InfiniiVision Oscilloscopes User’s Guide 417CSV and ASCII XY filesCSV and ASCII XY file structureIn CSV or ASCII XY format the Length con

15 Reference418 InfiniiVision Oscilloscopes User’s GuideAcknowledgementsRealVNC is licensed under the GNU General Public License. Copyright (C) 2002-

Reference 15InfiniiVision Oscilloscopes User’s Guide 419To return the instrumentBefore shipping the oscilloscope to Agilent Technologies, contact you

2 Initial Setup42 InfiniiVision Oscilloscopes User’s Guide7000 Series OverlayA front panel overlay which labels the controls is available in Simplifi

15 Reference420 InfiniiVision Oscilloscopes User’s GuideContact usAmericasCanada (877) 894-4414Latin America 305 269 7500United States (800) 829-4444

InfiniiVision Oscilloscopes User’s Guide 421IndexSymbols(-)Width measurement, 202(+)Width measurement, 202Numerics1 M ohm input impedance, 6110 MHz r

Index 422 InfiniiVision Oscilloscopes User’s Guidecalibration protect switch5000 Series, 3626000 Series, 3646000-BAT Series, 364, 3667000 Series, 367c

Index InfiniiVision Oscilloscopes User’s Guide 423EEPROM data read, I2C trigger, 117energy of a pulse, 232Entry knob, 53, 176, 360event table, 293expa

Index 424 InfiniiVision Oscilloscopes User’s Guideinvert, 62invert graticule colors, 251IP address, 275, 277JJapanese GUI, 56Kkeys, 535000/6000 Series

Index InfiniiVision Oscilloscopes User’s Guide 425new label, 184noisehigh-frequency, 88, 89low-frequency, 89noise rejection, 89normal acquire mode, 26

Index 426 InfiniiVision Oscilloscopes User’s Guidereplacement parts, 389reset LAN, 278restart condition, I2C trigger, 117return instrument for service

Index InfiniiVision Oscilloscopes User’s Guide 427totalizer, UART/rs232, 334tracesave to scope memory, 256save to USB, 255tracking cursors, 215transie

Index 428 InfiniiVision Oscilloscopes User’s Guidewaveformcursor tracking, 215intensity, 180keys, 358printing, 244recall, 256reference point, 187save

Initial Setup 2InfiniiVision Oscilloscopes User’s Guide 43To mount the oscilloscope in a rackThe InfiniiVision oscilloscopes can be mounted in an Ele

2 Initial Setup44 InfiniiVision Oscilloscopes User’s Guide1 Loosely attach the Front Extender Supports to the Rear Extender Supports with four (4) cl

Initial Setup 2InfiniiVision Oscilloscopes User’s Guide 45a Attach a Rack Mount Extender to the left side of the oscilloscope using two (2) of the M3

2 Initial Setup46 InfiniiVision Oscilloscopes User’s Guide6000L Mounting Bracket DimensionsThe following information is provided in case you want to

Initial Setup 2InfiniiVision Oscilloscopes User’s Guide 47Ventilation RequirementsThe air intake and exhaust areas must be free from obstructions. Un

2 Initial Setup48 InfiniiVision Oscilloscopes User’s GuidePower Requirements5000, 6000A (without Option BAT), and 7000 Line voltage, frequency, and p

Initial Setup 2InfiniiVision Oscilloscopes User’s Guide 49Power-on the 5000/6000/7000 Series Oscilloscope1 Connect the power cord to the rear of the

InfiniiVision Oscilloscopes User’s Guide 59Web InterfaceSetting up the I/O port, establishing LAN connection, using the oscilloscope’s web interface.

2 Initial Setup50 InfiniiVision Oscilloscopes User’s GuideThe battery will last approximately 1.75 hours before requiring recharging. Operating time

Initial Setup 2InfiniiVision Oscilloscopes User’s Guide 512 Always connect the supplied ground wire from the ground post on the back of the instrumen

2 Initial Setup52 InfiniiVision Oscilloscopes User’s GuideCharging the BatteryWhen charging the battery, the operating temperature should be in the r

Initial Setup 2InfiniiVision Oscilloscopes User’s Guide 53Keys, Softkeys, and the Entry KnobOn the front panel, “key” refers to any key (button) you

2 Initial Setup54 InfiniiVision Oscilloscopes User’s GuideVerifying Basic Oscilloscope OperationIf you have a 6000L Series oscilloscope, you need to

Initial Setup 2InfiniiVision Oscilloscopes User’s Guide 55Quick HelpTo view Quick Help1 Press and hold the key or softkey for which you would like to

2 Initial Setup56 InfiniiVision Oscilloscopes User’s GuideQuick Help Languages To choose a Quick Help language in the oscilloscope:1 Press [Utility],

Initial Setup 2InfiniiVision Oscilloscopes User’s Guide 57To set the clockThe Clock Menu lets you set the current date and time of day (24-hour forma

2 Initial Setup58 InfiniiVision Oscilloscopes User’s GuideTo set up the screen saverThe oscilloscope can be configured to turn on a display screen sa

Initial Setup 2InfiniiVision Oscilloscopes User’s Guide 594 Press the Preview softkey to preview the screen saver you have selected with the Saver so

6 InfiniiVision Oscilloscopes User’s Guide

2 Initial Setup60 InfiniiVision Oscilloscopes User’s GuidePressing an analog channel key displays the channel’s menu and turns the display of the cha

Initial Setup 2InfiniiVision Oscilloscopes User’s Guide 61Channel Coupling and Input Impedance Selection3 Press the channel’s on/off key, then press

2 Initial Setup62 InfiniiVision Oscilloscopes User’s Guide• 1M Ohm mode is for use with many passive probes and for general-purpose measurements. The

Initial Setup 2InfiniiVision Oscilloscopes User’s Guide 63• Probe Attenuation Factor— This is set automatically if the oscilloscope can identify the

2 Initial Setup64 InfiniiVision Oscilloscopes User’s GuideTo set up the Horizontal time base 1 Press the [Menu/Zoom] key (or [Main/Delayed] key on so

Initial Setup 2InfiniiVision Oscilloscopes User’s Guide 653 Press the Fine softkey to turn on the time base fine adjustment.The Fine softkey lets you

2 Initial Setup66 InfiniiVision Oscilloscopes User’s Guidedelay time set to 400 s. The delay time number tells you how far the time reference point

Initial Setup 2InfiniiVision Oscilloscopes User’s Guide 67When the horizontal mode is set to Normal, the horizontal position control (delay control)

2 Initial Setup68 InfiniiVision Oscilloscopes User’s GuideTo specify the measurement window for Zoom mode When the zoomed time base is displayed, you

Initial Setup 2InfiniiVision Oscilloscopes User’s Guide 69XY modeXY mode changes the display from a volts-versus-time display to a volts-versus-volts

InfiniiVision Oscilloscopes User’s Guide 7ContentsBook Map 3In This User’s Guide… 41 Introduction 21Models Covered in this Manual 22Specifications an

2 Initial Setup70 InfiniiVision Oscilloscopes User’s Guide

71Agilent InfiniiVision 5000/6000/7000 Series OscilloscopeUser’s Guide 3Connecting to the Device Under TestAnalog Input Impedance (50 Ohm or 1 MOhm)

3 Connecting to the Device Under Test72 InfiniiVision Oscilloscopes User’s GuideAnalog Input Impedance (50 Ohm or 1 MOhm)The input impedance of most

Connecting to the Device Under Test 3InfiniiVision Oscilloscopes User’s Guide 73Passive Probes All InfiniiVision oscilloscopes recognize passive prob

3 Connecting to the Device Under Test74 InfiniiVision Oscilloscopes User’s GuideActive Probes Most Agilent active probes are compatible with the Auto

Connecting to the Device Under Test 3InfiniiVision Oscilloscopes User’s Guide 75Active Probes for 6000 Series 100 MHz Bandwidth ModelsThe following a

3 Connecting to the Device Under Test76 InfiniiVision Oscilloscopes User’s GuideCAUTIONMaximum input voltage at analog inputs: CAT I 300 Vrms, 400 Vp

Connecting to the Device Under Test 3InfiniiVision Oscilloscopes User’s Guide 77Compensating Passive ProbesEach oscilloscope passive probe must be co

3 Connecting to the Device Under Test78 InfiniiVision Oscilloscopes User’s GuideCalibrating ProbesSome probes, such as the 10073C, 10074C, and 1165A

Connecting to the Device Under Test 3InfiniiVision Oscilloscopes User’s Guide 79• 10:1 (+20 dB Atten) single-ended browser• 10:1 (+20 dB Atten) diffe

Contents8 InfiniiVision Oscilloscopes User’s GuideTo mount the oscilloscope in a rack 43To mount the 5000 or 6000 Series oscilloscope in a rack 43To

3 Connecting to the Device Under Test80 InfiniiVision Oscilloscopes User’s GuideManually Setting the Probe Attenuation FactorThe probe attenuation fa

81Agilent InfiniiVision 5000/6000/7000 Series OscilloscopeUser’s Guide 4TriggeringTriggering - General Information 83Trigger Mode and Coupling Menu

4 Triggering82 InfiniiVision Oscilloscopes User’s GuideThis chapter provides instructions for setting up triggers for various signal types. Setups ca

Triggering 4InfiniiVision Oscilloscopes User’s Guide 83Triggering - General InformationA triggered waveform is one in which the oscilloscope begins t

4 Triggering84 InfiniiVision Oscilloscopes User’s GuideTrigger Mode and Coupling Menu• Press the [Mode/Coupling] key in the Trigger section of the fr

Triggering 4InfiniiVision Oscilloscopes User’s Guide 85Auto ModeUse the auto trigger modes for signals other than low-repetitive-rate signals and for

4 Triggering86 InfiniiVision Oscilloscopes User’s Guidepre-trigger buffer, the trigger will not be found. If you use Normal mode and wait for the tri

Triggering 4InfiniiVision Oscilloscopes User’s Guide 87Trigger Coupling1 Press the [Mode/Coupling] key.2 Press the Coupling softkey, then select DC,

4 Triggering88 InfiniiVision Oscilloscopes User’s GuideHF RejectHF Reject adds a 50 kHz low-pass filter in the trigger path to remove high frequency

Triggering 4InfiniiVision Oscilloscopes User’s Guide 89LF RejectLow-frequency reject (LF reject) adds a high-pass filter with the 3-dB point at 50 kH

Contents InfiniiVision Oscilloscopes User’s Guide 9AutoProbe Interface 72Passive Probes 73Active Probes 74Active Probes for 6000 Series 100 MHz Bandwi

4 Triggering90 InfiniiVision Oscilloscopes User’s GuideTrigger HoldoffTrigger Holdoff Operating HintsHoldoff keeps a trigger from occurring until aft

Triggering 4InfiniiVision Oscilloscopes User’s Guide 91By setting the Holdoff, you can synchronize triggers. The oscilloscope will trigger on one edg

4 Triggering92 InfiniiVision Oscilloscopes User’s GuideExternal Trigger InputThe External Trigger input can be used as a source in several of the tri

Triggering 4InfiniiVision Oscilloscopes User’s Guide 93Input Impedance The 2-channel oscilloscopes have selectable external trigger input impedance.

4 Triggering94 InfiniiVision Oscilloscopes User’s Guide4-Channel Oscilloscope External Trigger InputInput Impedance The external trigger input impeda

Triggering 4InfiniiVision Oscilloscopes User’s Guide 95Trigger OutputYou can select one of the following signals to be output at the TRIG OUT connect

4 Triggering96 InfiniiVision Oscilloscopes User’s GuideTrigger TypesThe oscilloscope lets you synchronize the display to the actions of the device un

Triggering 4InfiniiVision Oscilloscopes User’s Guide 97Changes to the trigger specification are applied when you make them. If the oscilloscope is st

4 Triggering98 InfiniiVision Oscilloscopes User’s GuideCAN TriggerThe Controller Area Network (CAN) trigger allows triggering on CAN version 2.0A and

Triggering 4InfiniiVision Oscilloscopes User’s Guide 995 Press the Settings softkey to display CAN Trigger Menu.6 Repeatedly press and release the Tr