Agilent Technologies E6392B Betriebsanweisung Seite 159
- Seite / 206
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
158 Chapter 3
Screen Reference
CONFIGURATION
Creating Instruction Messages
An instruction message with up to 69 characters including spaces and symbols can
be created for each step of a test flow to execute AUTOMATIC TEST. The range
of the step numbers is from 1 to 7 corresponding to each step of a test flow. Use the
following procedure to create an instruction message:
Step 1. Place the circular cursor in front of the input field of Instruction.
Step 2. Press and rotate the CURSOR CONTROL knob until the desired step number is
shown and press the CURSOR CONTROL knob to select it. Then, the whole
message line is displayed with the rectangular cursor on the first position, showing
a message if it is already stored. Check that the circular cursor is set to Done in the
Choices scrolling window.
Step 3. Create a message by rotating and pressing the CURSOR CONTROL knob to select
commands, alphanumeric characters, and some kinds of symbols from the
scrolling window.
The available commands and characters are as follows:
o Done: Enters the newly created instruction message in the instruction message
field.
o Cancel: Exits the editing function without any change of the message.
o Position: Allows you to move the rectangular cursor to any position of the
message for editing.
- Agilent Technologies 2
- E6392B GSM MS Test Set 2
- User’s Guide 2
- Manual Part Number 3
- E6392-90051 3
- Information 4
- ACOUSTIC NOISE EMISSION 7
- GERXUSCHEMISSION 7
- Contents 10
- 1 Preparing for Use 14
- Major Functions 15
- 16 Chapter 1 17
- Preparing for Use 17
- Installing the Test Set 18
- Power Cable 19
- Chapter 1 19 20
- 1. Preparing for Use 20
- Line Settings 21
- Environment 21
- Replacing the Line Power Fuse 22
- Warm-Up Time 22
- Preparation for Each Test 23
- UUT Connections 24
- Entering Attenuations 25
- Troubleshooting 26
- 26 Chapter 1 27
- 2 Using Functions 28
- 28 Chapter 2 29
- Using Functions 29
- Chapter 2 29 30
- 2. Using Functions 30
- 30 Chapter 2 31
- Chapter 2 31 32
- 32 Chapter 2 33
- Chapter 2 33 34
- 34 Chapter 2 35
- Chapter 2 35 36
- 36 Chapter 2 37
- Chapter 2 37 38
- 38 Chapter 2 39
- Chapter 2 39 40
- 40 Chapter 2 41
- Chapter 2 41 42
- 42 Chapter 2 43
- Chapter 2 43 44
- 44 Chapter 2 45
- Chapter 2 45 46
- 46 Chapter 2 47
- Chapter 2 47 48
- 48 Chapter 2 49
- Chapter 2 49 50
- 50 Chapter 2 51
- 3 Screen Reference 52
- General Operation Guide 53
- Chapter 3 53 54
- Rear Panel Overview 55
- Display Annotation 56
- Screen Flow Chart 57
- Figure 3-5 Screen Flow Chart 58
- Option 002 58
- Option 040 58
- 58 Chapter 3 59
- Storing Two Numeric Values 60
- Recalling the Numeric Values 61
- Variable Increment Softkey 61
- Initial Screen 62
- 62 Chapter 3 63
- AUTOMATIC TEST 64
- 64 Chapter 3 65
- Talk Measuring Screen 70
- Aborted Screen 72
- Pass/Fail Screen 74
- Pass/Fail Screen Examples 76
- 76 Chapter 3 77
- Chapter 3 77 78
- 78 Chapter 3 79
- Pass/Fail: DC Current 80
- Measurement Mode Selection 81
- Test SIM 81
- Chapter 3 87 88
- Talk/RF Test Measuring Screen 89
- Chapter 3 89 90
- Chapter 3 91 92
- 92 Chapter 3 93
- Chapter 3 93 94
- Softkey Menu 3 95
- Chapter 3 95 96
- Chapter 3 97 98
- Chapter 3 99 100
- Screen Reference 100
- 3. Screen Reference 100
- Screen Fields 101
- 102 Chapter 3 103
- Stand-by Screen 104
- Explanation 107
- Measuring Screen 108
- Measuring Screen Examples 109
- Chapter 3 109 110
- 110 Chapter 3 111
- Chapter 3 111 112
- 112 Chapter 3 113
- Measuring: DC Current 114
- Measuring: Spectrum Monitor 115
- Chapter 3 115 116
- MANUAL TEST (GPRS Mode) 119
- Idle Screen 124
- Attached Screen 125
- CONTROL knob 126
- Chapter 3 127 128
- 128 Chapter 3 129
- Chapter 3 129 130
- 130 Chapter 3 131
- Chapter 3 133 134
- SPECTRUM MONITOR 137
- Measuring Screens 141
- Chapter 3 141 142
- 142 Chapter 3 143
- SIGNAL GENERATOR 144
- CONFIGURATION 146
- 148 Chapter 3 149
- Chapter 3 153 154
- Automatic Test Flow 155
- Creating Instruction Messages 159
- Chapter 3 159 160
- File Management 161
- Saving a Test Setup File 162
- 162 Chapter 3 163
- Recalling a Test Setup File 164
- 164 Chapter 3 165
- How to Update the Firmware 166
- 166 Chapter 3 167
- 4 Functionality/Operation 168
- GSM Mobile Block Diagram 169
- GSM Measurements Selection 170
- 170 Chapter 4 171
- Functionality/Operation 171
- −50 to −90 dBm) 171
- −102 dBm) 171
- GPRS Overview 172
- 172 Chapter 4 173
- 5 Specifications 174
- General Information 175
- RF Input/Output 176
- RF Signal Generator 176
- RF Analyzer 177
- Spectrum Monitor 178
- DC Power Supply 179
- DC Current Measurement 179
- Memory Card 179
- GPRS Test (Option 040) 181
- Rear Panel 182
- General Specifications 183
- A. General Information 184
- The GSM System 185
- Power Control Levels 186
- RX Level 187
- RX Quality 188
- Limits for BER and FER 188
- Limits for Frequency Error 188
- 188 Appendix A 189
- B. Input Fields and 190
- Allowable Ranges 190
- 192 Appendix B 193
- Appendix B 193 194
- 194 Appendix B 195
- C Manual Changes 196
- Introduction 197
Verwandte Produkte und Handbücher für Vernetzung Agilent Technologies E6392B
(100 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern