Agilent Technologies Switch/Measure Betriebsanweisung Seite 108
- Seite / 184
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
100 Agilent 34980A Mainframe User’s Guide
3 Features and Functions
Thermistor Measurements
The instrument supports 2.2 k (YSI Series 44004), 5 k (YSI Series 44007),
and 10 k
(YSI Series 44006) thermistors.
Front Panel Operation: To select the thermistor function for the active
channel, choose the following items.
DMM or Channel (Configure) > TEMPERATURE > PROBE TYPE > THERMISTOR
To select the thermistor type for the active channel, choose from the
following items.
THERMISTOR TYPE > 10K|5K|2.2K
Remote Interface Operation: You can use the CONFigure or MEASure?
command to select the probe type and thermistor type. For example,
the following command configures channel 3001 for measurements of a
5 k
thermistor:
CONF:TEMP THER,5000,(@3001)
You can also use the SENSe command to select the probe type and
thermistor type. For example, the following command configures channel
1003 for measurements of a 10 k
thermistor:
SENS:TEMP:TRAN:THERM:TYPE 10000,(@1003)
- Agilent 34980A 1
- Multifunction 1
- Switch/Measure Unit 1
- *34980-90005* 1
- Additional Safety Notices 3
- Contents 5
- Introduction to the 34980A 9
- Data Acquisition Overview 10
- Measurement Software 11
- 1 Introduction to the 34980A 12
- Web Browser Interface 12
- Data Acquisition Circuitry 13
- Plug-In Modules 14
- System Cabling 14
- Transducers and Sensors 15
- Signal Routing and Switching 16
- Matrix Switching 17
- General Purpose Switching 17
- RF and Microwave Switching 18
- Measurement Input 19
- Main System Processor 20
- The Digital Modules 24
- Tota li z e r 25
- Control Output 26
- Voltage (DAC) Output 27
- 16V or dc current up to 27
- Getting Started 29
- Front Panel at a Glance 30
- Rear Panel at a Glance 31
- Rear Panel Connector Pinouts 32
- Removing a Slot Cover 34
- Installing a Module 35
- 2 Getting Started 36
- Wiring a Terminal Block 37
- Installing a Terminal Block 38
- Getting Started 2 39
- Instrument Rack Mounting 40
- Front Panel Menu Reference 43
- Configure Key Group 44
- Using the Measure Keys 47
- Connecting Over LAN 54
- Connecting Via Site LAN 55
- Connecting Over GPIB 59
- Connecting Over USB 60
- Communicating with the 34980A 61
- Launching the Web Interface 62
- Analog Bus Overview 65
- 34980A Documentation Map 69
- Features and Functions 71
- Module and Channel Status 72
- Menu Choices 72
- Readings 72
- Annunciators 72
- Front Panel Controls 73
- Basic Operating Modes 74
- SCPI Commands 74
- GPIB Interface 77
- LAN Interface 77
- Analog Buses 92
- Measurement Functions 93
- Measurement Range 94
- Measurement Resolution 95
- Custom A/D Integration Time 96
- Autozero 97
- Trigger Delay 98
- Automatic Trigger Delays 99
- Safety Interlock 100
- User-Defined Channel Labels 101
- 3 Features and Functions 102
- 2-Wire Versus 1-Wire Mode 103
- Measurement Units 104
- Thermocouple Measurements 105
- RTD Measurements 106
- Thermistor Measurements 108
- DC Input Resistance 109
- AC Low Frequency Filter 110
- Remote Interface Operation: 111
- Low Frequency Timeout 113
- Mx+B Scaling 114
- Front Panel Operation: 115
- Scanning 116
- Features and Functions 3 117
- Scan Trigger Source 120
- Manual Scanning 121
- Scanning on Alarm 122
- External Scanning 124
- Trigger Count 125
- Sweep Count 125
- Sample Count 126
- (1 to 500,000 samples) 126
- Trigger Trigger 126
- Channel Delay 128
- Automatic Channel Delays 129
- Relative Format (Default): 131
- Absolute Format: 131
- Non-Sequential Scanning 132
- Monitor Mode 135
- Alarm Limits 140
- Upper Limit 141
- Lower Limit 141
- Alarm Event No Alarm 141
- Viewing Stored Alarm Data 143
- Using the Alarm Output Lines 144
- Sequences 148
- ROUT:SEQ:DEF? MYSEQ_1 151
- Executing a Sequence 152
- Deleting Sequences 154
- System-Related Operations 155
- CANCEL 156
- Error Conditions 158
- Front-Panel Display Control 159
- Front-Panel Number Format 160
- Internal DMM Disable 161
- Relay Cycle Count 162
- SCPI Language Version 162
- Calibration Overview 163
- Calibration Count 164
- Calibration Message 165
- Factory Reset State 166
- Instrument Preset State 168
- Agilent Technologies 171
- Comments 173
- ±300V 1A 45 MHz 100 <3 173
- General Considerations 176
- per channel 177
- Vrms or VDC, 177
Verwandte Produkte und Handbücher für Netzwerk-Switches Agilent Technologies Switch/Measure
(28 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern