Agilent Technologies 1912A Bedienungsanleitung PDF herunterladen (Seite 4)

To protect users’ investments in the

E4418/4419B, the new N1913/1914A

is designed to be compatible with 848x,

N848x, E930x, and E441x Series power

sensors as well as the U2000 Series

USB power sensors (with power meter

USB port option). The compatibility of

power sensors with the N1913/1914A

allows full functionality with a

minimum of software modiﬁcation.

Figure 3. The Agilent 848x, N848x, E930x, E441x, and U2000 Series USB power sensors that

are supported by the N1913/1914A

The N1913/1914A provides SCPI

backward compatibility with the

E4418/4419B. It will make it

easier for the users to replace the

existing E4418/4419B with the new

N1913/1914A. The N1913/1914A uses

the same remote commands or SCPI

as the E4418/4419B for instrument

conﬁguration and measurement

settings.

The N1913/1914A also provides code

compatibility or an emulation mode

(43X compatibility option N191xA-200)

for conventional 436A, 437B, and 438A

power meter. For further information

about emulation mode, please refer

to Agilent EPM Series 437B and

438A Compatibility Application Note,

literature number 5968-4519E.

The existing IVI-COM driver of the

E4418/4419B has been modiﬁed

to function with the N1913/1914A.

This driver support is important for

customers who want to replace the

E4418/4419B with N1913/1914A.

SCPI/Programming Compatibility

Power Sensor Compatibility

The U2000 Series USB power sensor can be operated on the PC Windows platform

via the Agilent N1918A Power Analysis Manager software. It can also be controlled

through the N1913/1914A’s front panel. Alternatively, SCPI compatibility with the

N1913/1914A allows the users to control the USB power sensor remotely.

Subsystems such as SENSe, SERVice, TRIGger, and CALibration are

applicable and allow N1913/1914A to communicate with the USB power sensors

connected to Channel C & D via SCPI. To communicate with the USB power sensor

that is connected to Channel C, refer to SENS3, SERV3, TRIG3, or CAL3. To

communicate with the USB power sensor that is connected to Channel D, refer to

SENS4, SERV4, TRIG4, or CAL4.

Table 2 shows the IEEE 488.2 Common Commands that are not applicable for the

USB power sensor when it is connected to Channel C or D of the N1913/1914A.

The Common Commands apply only to the N1913/1914A, except the *RST. This

command will reset the N1913/1914A and the USB power sensor as well.

USB Power Sensor SCPI Compatibility

IEEE 488.2 Common Commands Description

*CLS

Clear status

*ESE and *ESE?

Event status enable

*ESR?

Event status register

*IDN?

Identify

*OPC and *OPC?

Operation complete

*OPT?

Options

*RCL

Recall

*SAV

Save

*SRE and *SRE?

Service request enable

*STB?

Status byte

*TRG

Trigger

*TST?

Test

*WAI

Wait

Table 2. The IEEE 488.2 Common Commands that are not supported by USB power sensors

through the N1913/1914A power meter

1 2 3 4 5 6 7 8 9 ... 13 14

Kommentare zu diesen Handbüchern

Keine Kommentare

Agilent Technologies 1912A Bedienungsanleitung Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Multimeter Agilent Technologies 1912A