Agilent Technologies Agilent 4396B Bedienungsanleitung

Specifications describe the instrument’swarranted performance over the temperature range of 0 °C to 40 °C(except as noted). Supplemental characteristi

10Typical Dynamic RangeFigure 6. Typical dynamic range at S inputFigure 7. Typical dynamic range at R, A, and B inputsDynamic range (dB)Input level (d

11Spurious responsesSecond harmonic distortion≥ 10 MHz, –35 dBm mixer input . . . . . . . . . . . . . . . . . . . . . . . . .< –70 dBc< 10 MHz

12Frequency response2 ±5 °C, aft. = 10 dB, referenced to level at 20 MHz10 MHz ≤ frequency ≤ 1.8 GHz . . . . . . . . . . . .< ±0.5 dB (±0.3 dB typ

13Sweep characteristicsSweep type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Linear, zero span, listTrigger type . . . .

14Input and Output CharacteristicsRF inputConnector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Type-N femaleImped

15Specifications when Option 4396B-1D6 time-gated spectrum analysis is installedGate lengthRange . . . . . . . . . . . . . . . . . . . . . . . . . .

16Impedance Measurement (Option 4396B-010)Measurement functionsMeasurement parameters . . . . . . . . . . . . . . . . . . . . . . .Z, Y, L, C, Q, R,

17External DC bias input1Maximum voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±40 VMaximum current

18IZI – θ accuracyIZI accuracy Za= A + (B/IZmI + C x IZmI) x 100[%]θ accuracy θa= sin–1(Za/100)Where, is IZmI is IZI measured. A, B, and C are obtai

19IYI – θ accuracyIYI accuracy Ya= A + (B x IYmI + C/IYmI ) x 100[%]θ accuracy θa= sin–1(Ya/100)Where, IYmI is IYI measured. A, B, and C are obtained

2Output CharacteristicsPower range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .–60 dBm to +20 dBm Power sweep range .

20D accuracyAccuracy D ≤ 0.2 0.2 < DDaza/100 (za/100) x (1 + D2)Where Zais IZI accuracy.L accuracy (depends on D)Accuracy D ≤ 0.2 0.2 < DLaLa/10

21Common Specifications for Network and Spectrum MeasurementDisplayTFT LCDSize/type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

22Probe powerOutput voltage . . . . . . . . . . . . +15 V (300 mA), –12.6 V (160 mA), GND nominalKeyboardConnector . . . . . . . . . . . . . . . . . .

232nd IF outputFrequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21.42 MHz nominaloutput impedance . . . . . . .

24S-parameter test set interfaceConnector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-SUB (25 pin)External m

25OthersEMC1. . . . . Complies with CISPR 11(1990) / EN 55011 (1991): Group 1, Class AComplies with IEC 801-2 (1991) / EN 50082-1 (1992): 4 kV CD, 8

26

27

Agilent Technologies’ Test and Measurement Support, Services, and AssistanceAgilent Technologies aims to maximize the value you receive, while minimiz

3Receiver CharacteristicsInput characteristicsFrequency rangeIFBW ≤ 3 kHz . . . . . . . . . . . . . . . . . . . . . . . . .100 kHz to 1.8 GHzIFBW = 1

4Magnitude CharacteristicsAbsolute amplitude accuracy (R, A, B)–20 dBm input, 23 ±5 °C . . . . . . . . . . . . . . .< ±1.5 dB (±0.9 dB typically)R

5Phase CharacteristicsMeasurements format . . . . . . . . . . . . . . .Phase format, expanded phase format Frequency response (deviation from linear

6Group Delay CharacteristicsAccuracyIn general, the following formula can be used to determine the accuracy, in seconds, of a specific group delay m

7Spectrum MeasurementSpecifications in this section describe the instrument’s warranted performancefor spectrum measurement using S input (except as n

8Noise sidebandsOffset from carrier Noise sidebands1≥ 1 kHz < –95 dBc/Hz≥ 10 kHz < –105 dBc/Hz≥ 1 MHz < –110 dBc/HzResidual FMRBW ≤ 10 HzOpti

9On-screen dynamic range1 GHz center frequency, may be limited by average noise level.Amplitude characteristicsAmplitude range . . . . . . . . . . . .