Agilent Technologies 54501A Spezifikationen Seite 118
- Seite / 168
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
85330A Multiple Channel Controller 7-7
Remote Programming Command Reference
Standard Command Reference
RUNTime
Subsystem Command Syntax
RUNTime
:CONTroller CONTroller | REMote1 | REMote2;
:EVENt
:COUNt <number of primary increment angles>;
:TRIGger IMM | TTL;
:INITiate
:IMM;
:SWITch
:DELay <microseconds>;
:SCAN port,(@switch address [,switch address]);
:TRIGger IMM | REMote1 | REMote2;
:SOURce
:COUNt <number of frequency points>;
:SOURCE1
:TRIGger IMM | TTL | REMote1 | REMote2;
:SOURCE2
:TRIGger IMM | TTL | REMote1 | REMote2;
:TIMEout
:EVENt 0 | 1, <microseconds>;
:RECeiver <microseconds>;
:REMote <microseconds>;
:SOURCE <microseconds>;
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
- 1
- Agilent Technologies 85330A 2
- Multiple Channel Controller 2
- Restricted Rights Legend 3
- Warranty 5
- Service and Support 6
- Instrument Markings 7
- Safety Earth 8
- Manufacturers Declaration 10
- DECLARATION OF CONFORMITY 11
- Typeface Conventions 12
- Contents 14
- 1 Installation 20
- Choosing the Proper 21
- Installation 22
- Controller 25
- Procedure 26
- Triggers 27
- • SCU address is set to 0 29
- 2 Performance Verification 32
- Recommended 33
- Equipment 33
- Performance Verification Test 34
- Setting Up the Equipment 34
- {Coupling: DC} 35
- Measurement Display 36
- Performance Verification 37
- Pulse Receive and 39
- Cycle Test 39
- Counter Pulse Delay 40
- 12. Remove the BNC cables 41
- Width Test 42
- Measurement Busy 42
- Signal and Pulse 42
- Verifying the RF Switches 44
- • Jumper (see below) 46
- • Soldering iron 46
- • 2 jumper wires 46
- AUX 1 and AUX 2 48
- Output Voltage Test 49
- When Finished with 49
- All Tests 49
- 3 Operator’s Check 50
- Operator’s Check 51
- 4 General Information 52
- Measurement Speed Advantages 53
- Triggering 53
- • Perform service functions 54
- Switch control units 55
- The Downloadable 56
- • Option 001: 1 meter 57
- • Option 002: 2 meters 57
- • Option 005: 5 meters 57
- • Option 010: 10 meters 57
- • A switch control unit (SCU) 58
- General Information 59
- Characteristics 60
- Ventilation 61
- Requirements 61
- Dimensions 61
- Need More 62
- Information 62
- Rear Panel Features 63
- SWITCH PORT 1 and 2 65
- AUX POWER IN 65
- 85330A Compatibility 66
- 5 Manual Operation 68
- To Use the Front Panel 69
- Softkey Map 70
- Changing the GPIB 71
- (to select a channel) 72
- Manual Operation 73
- To Perform Service Functions 74
- 6 Programming 76
- Definition of Terms 77
- • CW Measurement Configuration 78
- • 8530A Control of Sources 78
- • Fast Source Control 78
- CW Measurement Configuration 79
- To Use this 80
- 85330A settings 81
- 8530A Control of Sources 82
- Fast Source Control 83
- To Use Direct Control 84
- In this example: 86
- To Use Run-Time Control Mode 87
- TTL Trigger and 88
- Ready Timeouts 88
- Select Switch State 89
- Event Trigger 90
- Receiver Ready 90
- Switch List Loop 90
- Frequency Loop 92
- Event Loop 92
- Programming 100
- Programming Examples 100
- 85330A Error Messages 109
- 7 Remote Programming Command 112
- Abbreviated Commands 113
- Parameters 113
- Common Commands 114
- Syntax *OPC? 115
- Syntax *RST 115
- Example OUTPUT 70918;”*RST” 115
- Standard Command Reference 116
- ROUTe:CLOSe 116
- ROUTe:CONTrol 117
- ROUTe:DELay 117
- Subsystem Command Syntax 118
- :INITiate 118
- :TIMEout 118
- RUNTime:CONTroller 119
- RUNTime:EVENt:COUNt 119
- RUNTime:EVENt:TRIGger 120
- RUNTime:INITiate:IMM 121
- RUNTime:SOURce:COUNt 121
- RUNTime:SWITch:DELay 123
- RUNTime:SWITch:SCAN 124
- RUNTime:SWITch:TRIGger 125
- RUNTime:TIMEout:EVENt 126
- RUNTime:TIMEout:RECeiver 126
- RUNTime:TIMEout:REMote 127
- RUNTime:TIMEout:SOURce 127
- SYSTem:ERRor? 128
- 8 In Case of Difficulty 130
- In Case of Difficulty 131
- 9 Service 132
- Theory of Operation 133
- GPIB 134
- Recommended Test Equipment 138
- Troubleshooting 140
- 85383A Local Control Cable 142
- 85383B Expansion Cable 142
- 85384A Switch Driver Cable 142
- 85385A Remote Trigger Cable 142
- Table 9-5 85385A Wiring 143
- Replaceable Parts 144
- Mainframe, Plug-in 146
- Switch Control Unit 147
- RF Switch 147
- Interconnect Cables 148
- Assembly and Disassembly 149
- E1330 Card 150
- Configuration 150
- 85330-60002 Card 150
- Disassembly 151
- Assembly 151
- Adjustments 152
- Selecting the Multiple 153
- Channel Controller’s 153
- GPIB Address 153
- Switching from the 154
- Internal to External 154
- Power Supply 154
- Preventive Maintenance 155
- 10 Accessory Documentation 157
- Accessory Documentation 158
- A Glossary 159
- • Attaching cables 160
- Glossary 161
- Standard System 163
- Switch Address 163
- Switch Module 163
- Numerics 165
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.121 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern