Agilent Technologies E1411B Bedienungsanleitung PDF herunterladen (Seite 31)

Getting Started 25Chapter 1

Connecting User

Inputs

Figure 1-10 shows the front panel of the E1460A and the multiplexer’s

connector pin-out which mates to the terminal module. Actual user inputs

are connected to the terminal module. See "Wiring Terminal Modules" for

connection information.

Figure 1-10. E1460A Multiplexer Pin-Out

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 193 194

64-Channel Relay Multiplexer 1
Configuration 2
Product Specifications 2
General Specifications 2
Instrument Drivers 3
Module Current 3
Cooling/Slot 3
PDFINFO H 5 6 0 6 - 0 4 4
Ordering Information 5
Agilent Technologies 7
E1460A 64-Channel 7
Relay Multiplexer Module 7
User’s Manual 7
Documentation History 14
Declaration of Conformity 15
Getting Started 17
Channel Relay 18
Switches 18
Basic Operating 20
Configuring the Multiplexer 21
Setting the Logical 22
Address Switch 22
Setting the Status 23
Register Switch 23
Setting the Interrupt 23
Priority 23
Configuring the 24
Switch Card Wire 24
Reconfiguring the Relay 25
Mainframe 27
Installing the 27
Multiplexer in a 27
Connecting the 28
Analog Bus 28
Configuring Terminal Modules 29
Connecting User 31
Wiring Terminal 32
Attaching Terminal 34
Modules to the 34
Programming the Multiplexer 35
Addressing 36
Multiplexer Card 37
Multiplexer Channel 38
Addresses 38
Examples: Multiplexer 39
Module Channel List 39
Using the Relay Multiplexer 41
Switching Channels 43
Example: Switching 44
Channels (One-Wire) 44
Channels (Two-Wire) 45
Channels (Three-Wire) 46
Example: Switching 47
Channels (Four-Wire) 47
SWITCH CARD TERMINAL MODULE 48
Scanning Channels 49
Channels Using E1406A 50
Command Module 50
Channels Using E1412A 52
Multimeter 52
Channels Using 3457A 53
Multimeter DCV 55
Measurements 55
Multimeter Resistance 56
Example: Using the Scan 57
Complete Bit 57
Example: Connecting the 58
SWITCH CARD 60
TERMINAL MODULE 60
Example: Error Checking 62
Using Polling 62
Using Interrupts 63
Synchronizing the 64
Chapter 3 65
About This Chapter 65
Command Types 65
Variable Commands 66
SCPI Commands Reference 67
Subsystem Syntax ABORt 68
ARM:COUNt 69
ARM:COUNt? 70
INITiate 71
INITiate:CONTinuous? 72
INITiate[:IMMediate] 72
Enabling a Single Scan 73
OUTPut:ECLTrgn[:STATe] 74
OUTPut:ECLTrgn[:STATe]? 75
OUTPut[:EXTernal][:STATe] 75
OUTPut[:EXTernal][:STATe]? 76
OUTPut:TTLTrgn[:STATe] 76
OUTPut:TTLTrgn[:STATe]? 77
[ROUTe:] 78
[ROUTe:]CLOSe? 80
[ROUTe:]FUNCtion 81
[ROUTe:]FUNCtion? 82
Parameters 83
[ROUTe:]OPEN? 85
[ROUTe:]SCAN 85
[ROUTe:]SCAN:MODE? 88
[ROUTe:]SCAN:PORT 88
[ROUTe:]SCAN:PORT? 89
Subsystem Syntax STATus 90
Output Queue 91
Standard Event Register 91
Status Byte Register 91
Operation Status Register 91
STATus:OPERation:CONDition? 92
STATus:OPERation:ENABle 92
STATus:OPERation:ENABle? 92
STATus:OPERation[:EVENt]? 93
STATus:PRESet 93
Subsystem Syntax SYSTem 94
SYSTem:CPON 95
SYSTem:CTYPe? 95
SYSTem:ERRor? 96
TRIGger[:IMMediate] 97
TRIGger:SLOPe 98
TRIGger:SLOPe? 98
TRIGger:SOURce 98
TRIGger:SOURce? 100
<mask> 101
SCPI Commands Quick Reference 102
Appendix A 103
Register-Based Programming 105
A16 Address Space 106
Outside the Command 106
Module or Mainframe 107
Inside the Command 107
Register Descriptions 108
Status/Control 109
Register 109
ID and Device Type 110
Registers 110
Relay Control 110
Programming Examples 113
Example: 114
Opening/Closing 114
Multiplexer Channels 114
Example: Using a 116
Multimeter with a 116
Multiplexer 116
Example: Reading ID 117
Device Type 117
and Status Registers 117
Example: Scanning 118
Channels 118
Channels (HP-UX) 119
Appendix C 121
Index 121 127
122 Index 128
*E1460-90012* 129
Contents 131
WARNINGS 134
Printing History 134
Safety Symbols 134
DECLARATION OF CONFORMITY 135
General Information 139
Considerations 141
Incoming 143
Inspection 143
Shipping 144
Guidelines 144
Description 145
Recommended 146
Test Equipment 146
Verification Tests 147
Functional 149
Verification 149
Self-test Error 150
Agilent E1460A 151
Performance 151
Closed-channel 153
Resistance Test 153
Control Relay Test 155
Test 2-3: DC Isolation Test 158
High & Low 159
Example: DC Isolation 160
Test Record 161
Test Equipment Used: 163
High to Low 166
High & Low to Chassis 166
Replaceable Parts 167
(Continued on next page) 174
Chapter 4 179
Testing the 181
Assembly 181
Matching Relays 182
Maintenance 184
Component 185
Locators and 185
Schematic 185
Diagrams 185
Test 2-2: Testing 190
Control Relays 190
Test 2-3: DC 192
Isolation 192

Kommentare zu diesen Handbüchern

Keine Kommentare

Agilent Technologies E1411B Bedienungsanleitung Seite 31

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Multimeter Agilent Technologies E1411B