Agilent Technologies N5230C Betriebsanweisung PDF herunterladen (Seite 85)

User’s Guide 77

U3042AE12 Operational Check

8. To launch the Cal Set Viewer toolbar. Select Response > CAL > Manage CALS >

CAL Set Viewer.

Figure 61 Calibration, Cal Set Viewer

9. From the Cal Sets drop-down menu, select 999.1 and check Enable. Select the

Reflection Tracking(1,1) term in the center drop-down menu and ensure that the

Enable and Error Terms are selected.

NOTE You may also create a table on the PNA and enter the limit line stimulus and

response values. Select Limit Test ON and Limit Line ON, and press Show

Table. See Figure 62.

Figure 62 PNA-X Setting the Test Limits

1 2 ... 80 81 82 83 84 85 86 87 88 89 90 ... 101 102

Agilent Technologies 1
U3042AE12 1
Warranty Statement 2
Safety Notes 3
Statement of Compliance 3
Definitions 3
Contents 5
Introduction 10
Description 11
Available Options 12
Verifying the Shipment 13
General Specifications 14
Environmental Requirements 15
Table 4 System Dimensions 16
(significantly degraded 17
Typical Reflection Tracking 18
Front and Rear Panel Features 19
Line Switch 20
Test Set Interface 20
Pass Through Interface 20
Line Module 20
Available Fuses 21
System Setup with N5230A/C 22
User’s Guide 15 23
User’s Guide 17 25
Installing New Firmware 26
User’s Guide 19 27
Figure 11 N5230A Options 28
User’s Guide 21 29
22 User’s Guide 30
User’s Guide 23 31
24 User’s Guide 32
Use the scroll bar to 32
User’s Guide 25 33
26 User’s Guide 34
User’s Guide 27 35
N5230A Interface Control 36
User’s Guide 29 37
30 User’s Guide 38
User’s Guide 31 39
N5230A GPIB Control 40
User’s Guide 33 41
System Setup with N5242A 43
36 User’s Guide 44
User’s Guide 37 45
User’s Guide 39 47
40 User’s Guide 48
User’s Guide 41 49
42 User’s Guide 50
User’s Guide 43 51
44 User’s Guide 52
Use the scroll bar 53
46 User’s Guide 54
User’s Guide 47 55
48 User’s Guide 56
User’s Guide 49 57
50 User’s Guide 58
User’s Guide 51 59
52 User’s Guide 60
N5242A or N5230C GPIB Control 61
54 User’s Guide 62
DUT Control Lines 64
58 User’s Guide 66
U3042AE12 DUT Control Lines 66
User’s Guide 59 67
U3042AE12 DUT Control Lines 67
Switch Address and Data 69
6, 10 and 14 71
64 User’s Guide 72
8, 12 and 16 73
Operational Check 74
Equipment Required 75
Operational Check Procedure 76
User’s Guide 69 77
U3042AE12 Operational Check 77
70 User’s Guide 78
U3042AE12 Operational Check 78
User’s Guide 71 79
72 User’s Guide 80
User’s Guide 73 81
74 User’s Guide 82
User’s Guide 75 83
76 User’s Guide 84
User’s Guide 77 85
78 User’s Guide 86
User’s Guide 79 87
80 User’s Guide 88
Service Information 89
82 User’s Guide 90
U3042AE12 Service Information 90
Theory of Operation 91
RF Coupler Components 92
System Block Diagram 93
86 User’s Guide 94
U3042AE12 Theory of Operation 94
User’s Guide 87 95
Before Applying Power 96
Connector Care and Cleaning 96
Declaration of Conformity 96
Shipping Instructions 96
EMC Information 97
Safety Information 97
Warnings 98
Cautions 99
ICES/NMB-001 100
User’s Guide 93 101
Contacting Agilent 102

Kommentare zu diesen Handbüchern

Keine Kommentare

Agilent Technologies N5230C Betriebsanweisung Seite 85

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Messen, Testen & Steuern Agilent Technologies N5230C